Dell 6 series User Manual Download Page 129 | Manualshive

Page: 129 / 160

background image

Troubleshooting

129

Controller LED Indicators

The external SAS ports on the PERC 6/E adapter have a port status LED
per x4 SAS port. This bi-color LED displays the status of any external SAS
port. The LED indicates whether all links are functional or only partial links
are functional.
Table 7-9 describes the patterns for the PERC 6/E adapter port status.

smartd[smartd[2338]

Device: /dev/sda, Bad

IEC (SMART) mode page,

err=-5, skip device

smartd[2338] Unable to

register SCSI device

/dev/sda at line 1 of

file /etc/smartd.conf

This is a known issue. An unsupported
command is entered through the user
application. User applications attempt to direct
Command Descriptor Blocks to RAID volumes.
The error message does not effect the feature
functionality.

The

Mode Sense/Select

command is supported

by firmware on the controller. However, the
Linux kernel

daemon

issues the command to

the virtual disk instead of to the driver IOCTL
node. This action is not supported.

Table 7-9.

LED Behavior Patterns

Port State

LED State

Power-on state

Off

Reset state

Off

All links in port connected

Green light on

One or more links are not connected (applicable only in wide port
configurations)

Amber light on

All links in the port are disconnected or the cable is disconnected

Off

Table 7-8.

Linux Operating System Errors

(continued)

Error Message

Suggested Solution

Dell_PERC6.2_UG.book Page 129 Wednesday, June 24, 2009 6:08 PM

«
...
127
128
129
130
131
...
»

Summary of Contents for 6 series

































































































































































Reviews:

No comments

Related manuals for 6 series

Brand: QSC Pages: 28

Pixie-4 Express

Brand: XIA Pages: 17

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Valcom Pages: 4

Brand: Ubiquiti Pages: 21

Brand: Rainbow Pages: 2

Brand: Intercoax Pages: 2

Brand: IBM Pages: 64

Brand: PADAUK Pages: 27

CL-SOM-AM57 Series

Brand: CompuLab Pages: 79

Brand: Renesas Pages: 40

Brand: AMD Pages: 27

Brand: EXAGATE Pages: 7

Brand: ekwb Pages: 10

Brand: SilverStone Pages: 12

ServCon FPS-3003

Brand: LevelOne Pages: 45

Brand: Zhone Pages: 494

Brand: SeaLevel Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands