Dell 6 series User Manual Download Page 39

Page: 39 / 160

About PERC 6 and CERC 6/i Controllers

Patrol Read

adjusts the amount of controller resources dedicated to

Patrol Read

operations based on outstanding disk I/O. For example, if the

system is busy processing I/O operation, then

Patrol Read

uses fewer

resources to allow the I/O to take a higher priority.

Patrol Read

does not run on any disks involved in any of the following

operations:
•

Rebuild

•

Replace Member

•

Full or Background Initialization

•

Consistency Check

•

RAID Level Migration or Online Capacity Expansion

Patrol Read Modes

The following describes each of the modes

Patrol Read

can be set to:

•

Auto

(default)

— Patrol Read

is set to the

Auto

mode by default. In this

mode,

Patrol Read

is enabled to run automatically and start every seven

days on SAS and SATA HDDs.

Patrol Read

is not necessary on SSD and is

disabled by default. You can start and stop

Patrol Read

as well.

•

Manual

— Patrol Read

does not run automatically and you must start it

manually.

•

Disabled

— Patrol Read

is not allowed to start on the controller.

Dell_PERC6.2_UG.book Page 39 Wednesday, June 24, 2009 6:08 PM

Summary of Contents for 6 series

































































































































































Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands

Dell 6 series, User Manual

Search results

Summary of Contents for 6 series

Reviews:

Related manuals for 6 series

Brands by name

Popular brands