Dell 6 series User Manual Download Page 102 | Manualshive

Page: 102 / 160

background image

102

Configuring and Managing RAID

•

Performing the Replace Member operation

•

Setting the LED to blink

•

Making a disk online or offline (unaffiliated with a disk group)

•

Creating global hot spares

•

Removing dedicated hot spares or global hot spares

Physical Disk Actions

Table 6-5 describes the actions you can perform on physical disks.
For procedures that can be used to perform these actions, see "Physical Disk
Management" on page 105.

Table 6-5.

Physical Disk Actions

Action

Description

Rebuild

Regenerates all data to a replacement disk in a redundant
virtual disk (RAID level 1, 5, 6, 10, 50, or 60) after a disk
failure. A disk rebuild normally occurs without interrupting
normal operations on the affected virtual disk.

Replace Member

Replaces the drive in the virtual disk with another drive that
can be selected.

LED Blinking

Indicates when physical disks are being used to create a virtual
disk. You can choose to start or stop the LED blinking.

Force Online

Changes the state of the selected physical disk to online.

Force Offline

Changes the state of the selected physical disk so that it is no
longer part of a virtual disk.

Make Global HS

Designates the selected physical disk as a global hot spare.
A global hot spare is part of a pool for all virtual disks
controlled by the controller.
Designates the selected physical disk as a global hot spare.
You can select the hot spare to have enclosure affinity.

Remove HS

Removes a dedicated hot spare from its disk group or a global
hot spare from the global pool of hot spares.

Dell_PERC6.2_UG.book Page 102 Wednesday, June 24, 2009 6:08 PM

«
...
100
101
102
103
104
...
»

Summary of Contents for 6 series

































































































































































Reviews:

No comments

Related manuals for 6 series

Brand: 3Com Pages: 20

C50FSi - VB Network Camera

Brand: Canon Pages: 32

Brand: Rabbit Pages: 120

Brand: Acconeer Pages: 32

Brand: Sangoma Pages: 6

SAFETank Series

Brand: Raidon Pages: 49

eBOX532-100-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Zoom Pages: 48

Brand: Renesas Pages: 941

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: Pressalit Care Pages: 31

Brand: ACTi Pages: 12

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Xenteq Pages: 16

Brand: Maxtor Pages: 2

Brand: ICP DAS USA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands