BLEMO ER24 Series, Programming Manual

Page: 87 / 344

Configuration Mode (ConF)
89
Code Nam e / De s cription Adjus tment range Factory s e tting
FULL
[FULL] (continued)
SEt-
[SETTINGS]
Inr

0.01
0.1
1
[Ramp increment]
0.1
This parameter is valid for [Acce le ration] (ACC) , [De ce le ration] (dEC) , [Acce le ration 2] (AC2) and
[Decele ra tio n 2] (dE2) . See [Ra mp incre m e nt] (Inr) page 170 .
[0,01] : Ramp up to 99.99 seconds
[0,1] : Ramp up to 999.9 seconds
[1]
: Ramp up to 6,000 seconds
ACC

[Acceleration] 0.00 to 6,000 s (1) 3.0 s
Time to accelerate from 0 to the
[Rate d motor freq.]
(FrS) page 86 . To have repeatability in ramps, the value of this parameter
must be set according to the possibility of the application. See [Acce le ration] (ACC) page 170 .
dEC

[Deceleration]
0.00 to 6,000 s (1) 3.0 s
Time to decelerate from the [Rate d motor freq.] (FrS) page 86 to 0. To have repeatability in ramps, the value of this parameter
must be set according to the possibility of the application. See [De ce le ration] (dEC) page 170 .
AC2
*

[Acceleration 2]
0.00 to 6,000 s (1) 5 s
Time to accelerate from 0 to the [Rate d motor freq.] (FrS) page 86 . To have repeatability in ramps, the value of this parameter
must be set according to the possibility of the application. See
[Acce le ration 2]
(AC2) page 171 .
dE2
*

[Deceleration 2]
0.00 to 6,000 s (1) 5 s
Time to decelerate from the [Rate d motor freq.] (FrS) page 86 to 0. To have repeatability in ramps, the value of this parameter
must be set according to the possibility of the application. See
[De ce le ration 2]
(dE2) page 171 .
tA1
*

[Begin Acc round]
0 to 100% 10%
Rounding of start of acceleration ramp as a % of the [Acce le ration] (ACC) or [Acce leration 2] (AC2) ramp time. Visible if
[Ramp type]
(rPt) is set to
[Cust om ize d]
(CUS) . See
[Begin Acc round]
(tA1) page 170 .
tA2
*

[End Acc round]
0 to 100% 10%
Rounding of end of acceleration ramp as a % of the [Acce le ration] (ACC) or [Acce leration 2] (AC2) ramp time.
Can be set betw een 0 and 100% -
[Be gin Acc round]
(tA1) .
Visible if [Ra mp type] (rPt) is set to [Cust om ize d] (CUS) . See [End Acc round] (tA2) page 171 .
tA3
*

[Begin Dec round]
0 to 100% 10%
Rounding of start of deceleration ramp as a % of the [De ce le ration] (dEC) or [De ce le ration 2] (dE2) ramp time. Visible if
[Ramp type]
(rPt) is set to
[Cust om ize d]
(CUS) . See
[Begin Dec round]
(tA3) page 171 .
tA4
*

[End Dec round]
0 to 100% 10%
Rounding of end of deceleration ramp as a % of the [De ce le ration] (dEC) or [De ce le ration 2] (dE2) ramp time.
Can be set betw een 0 and 100% -
[Be gin De c round]
(tA3) .
Visible if [Ra mp type] (rPt) is set to [Cust om ize d] (CUS) . See [End Dec round] (tA4) page 171 .
LSP

[Low speed]
0 to 599 Hz 0 Hz
Motor frequency at minimum reference, can be set betw een 0 and [High s pe e d] (HSP) page 87 . See [Low s pe ed] (LSP)
page 87 .
HSP

[High speed] 0 to 599 Hz 50 Hz
Motor frequency at maximum reference, can be set between
[Low spee d]
(LSP) and
[Max freque n c y]
(tFr) . The factory
setting changes to 60 Hz if [Standard m ot. fre q] (bFr) is set to [60Hz NEM A] ( 0) . See [High s pe e d] (HSP) page 87 .
Parameters described in this page can be accessed by:
DRI- > CONF > FULL > SET-