BLEMO ER24 Series, Programming Manual

Page: 157 / 344

Configuration Mode (ConF)
159
Code Nam e / De s cription Adjus tment range Factory s e tting
FbrM [FB start mode] [No]
(nO)
2 s
WARNING
UNANTICIPATED EQUIPMENT OPERATION
Depending on the s etting of this param eter, function blocks m ay be im m ediately executed.
•
Verify that this s etting does not res ult in uns afe conditions.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Allow s to choose the different ways of starting the Function blocks application.
Note : Modifications of this parameter are not taken into account if the Function blocks application is running.
[No] (nO) : Function blocks application is controlled by [FB com m and] (FbCd) parameter
[Ye s ] (YES) : Function blocks application sw itches to Run automatically at drive pow er on
[LI1]
(LI1) : Function blocks application switches to Run on a rising edge of the logic input. It sw itch to Stop on falling edge of
the logic input.
[...] (...) : See the assignment conditions on page 153 (not [OL10] (OL01) to [OL10] (OL10) ).
nO
YES
LI1
...
FbSM
[Stop FB Stop motor]
[Fre e w heel] (YES)
nO
WARNING
LOSS OF CONTROL
If [Stop FB stop motor] (FbSM) is s et to [No] (nO) , the m otor will not s top when the program will be
s topped.
•
Only s et this param eter to [No] (nO) if you have im plem ented appropriate alternative s top functions .
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Allow s to setup the w ay of working of the drive w hen function blocks are stopped.
[Ignore ] (nO) : The drive does not stop
[Fre e w heel] (YES) : Motor stops in freew heel
[Ram p s top]
(rMP) : Ramp stop
[Fas t s top]
(FSt) : Fast stop
[DC inje ction] (dCI) : DC injection
YES
rMP
FSt
dCI
FbdF
StOP
IGn
[FB on drive fault]
[Stop] (StOP)
Behavior of function blocks w hen the drive trips.
[Stop]
(StOP) : Function blocks stops w hen the drive trips, outputs are realeased
[Ignore] (IGn) : Function blocks continue to w ork when the drive trips (except CFF and INFE)
FbA-
[INPUTS ASSIGNMENTS]
IL01
[Logic input 1 assignment]
[No] (nO)
nO
Possible assignment for the Function block logic input.
[No] (nO) : Not assigned
[No drive flt] (FLt) : Drive fault detection status (relay normally energized, and de-energized in the event of an error)
[Fre q. Th. attain.]
(FtA) : Frequency threshold attained (
[Fre q. thre s hold]
(Ftd) page 102 )
[Fre q. Th. 2 attaine d] (F2A) : Frequency threshold 2 attained ( [Fre q. thre s hold 2] (F2d) page 102 )
[Re f.1 channe l] (Fr1) Reference source 1
[Re f.2 channe l]
(Fr2) Reference source 2
[ch1 active ] (Cd1) : Command channel = channel 1 (for [Cmd sw itching] (CSS) )
[ch2 active ] (Cd2) : Command channel = channel 2 (for [Cmd sw itching] (CSS) )
[Ref.1 B channe l]
(Frlb) : Referenc e channel = channel 1b (for [Ref. 2 switching] (rFC) )
[Ye s ] (YES) : Yes
[LI1] (LI1) : Logical input LI1
[...]
(...) : See the assignment conditions on page 153
FLt
FtA
F2A
Fr1
Fr2
Cd1
Cd2
Fr1b
YES
LI1
...
IL-- [Logic input x assignment] [No] (nO)
All the Function Blocks logic inputs available on the drive are processed as in the example for
[Logic input 1 as s ignm e nt] (IL01) above, up to [Logic input 10 as s ignm e nt] (IL10) .