BLEMO ER24 Series, Programming Manual

Page: 171 / 344

Configuration Mode (ConF)
173
STOP CONFIGURATION
Code Nam e / De s cription Adjus tment range Factory s e tting
FUn-
[APPLICATION FUNCT.] (continued)
Stt- [STOP CONFIGURATION]
Note : Some types of stops cannot be used w ith all other functions. Follow the instructions on page 163 .
Stt
rMP
FSt
nSt
dCI
[Type of stop]
[Ram p s top] (rMP)
Stop mode on disappearance of the run command or appearance of a stop command.
Note :
If the "brake logic" function on page 194 has been enabled, or if
[Low s peed time out]
(tLS) page 95 or 213 is not 0,
only ramp type stops may be configured.
[Ram p s top]
(rMP) : Stop on ramp
[Fas t s top] (FSt) : Fast stop
[Free w he e l] (nSt) : Freew heel stop
[DC inject io n]
(dCI) : DC injection stop. Available only if
[M otor control type]
(Ctt) page 105 is not set to
[Sync. m ot.] (SYn) .
FFt
*

(1)
[Freewheel stop Thd.]
0.2 to 599 Hz 0.2 Hz
Speed threshold below which the motor w ill sw itch to freewheel stop.
This parameter supports sw itching from a ramp stop or a fast stop to a freew heel stop below a low speed threshold.
This parameter can be accessed if
[Type of s top]
(Stt) is set to
[Fas t s top]
(FSt) or
[Ram p s top]
(rMP) and if
[Brak e
as s ignm e nt] (bLC) or [Auto DC inje ction] (AdC) are configured.
nSt
nO
LI1
...
[Freewheel stop ass.] [No]
(nO)
The stop is activated w hen the input or the bit changes to 0. If the input returns to state 1 and the run command is still active, the
motor will only restart if
[2/3 wire contro l] (tCC) page 85 is set to [2 wire ] (2C) and if [2 wire type] (tCt) is set to
[Le ve l]
(LEL) or
[Fw d priority]
(PFO) . If not, a new run command must be sent.
[No] (nO) : Not assigned
[LI1]
(LI1) : Logical input LI1
[...] (...) : See the assignment conditions on page 153
FSt
nO
LI1
...
[Fast stop assign.] [No]
(nO)
The stop is activated w hen the input changes to 0 or the bit changes to 1 (bit in [I/O profile ] (IO) at 0).
If the input returns to state 1 and the run command is still active, the motor w ill only restart if [2/3 w ire
control]
(tCC) page 85 is set to
[2 wire ]
(2C) and if
[2 wire type]
(tCt) is set to
[Level]
(LEL) or
[Fwd priority ]
(PFO) .
If not, a new run command must be sent.
Note : This function cannot be used w ith certain other functions. Follow the instructions on page 163 .
[No] (nO) : Not assigned
[LI1] (LI1) : Logical input LI1
[...]
(...) : See the assignment conditions on page 153
dCF
*

(1)
[Ramp divider]
0 to 10 4
This paramet er can be accessed if
[Type of stop]
(Stt) is set to
[Fast stop]
(FSt) and if
[Fast stop assign.]
(FSt) is not
[No] (nO) and if [Stop type ] (PAS) is set to [Fas t s top] (FSt) .
The ramp that is enabled ( [De ce le ration] (dEC) or [De ce le ration 2] (dE2) ) is then divided by this coefficient when stop
requests are sent.
Value 0 corresponds to a minimum ramp time.
Parameters described in this page can be accessed by:
DRI- > CONF > FULL > FUN- > STT-