BLEMO ER24 Series, Programming Manual

Page: 262 / 344

Configuration Mode (ConF)
262
Code Nam e / De s cription Adjus tment range Factory s e tting
Behavior of the drive in the event of a communication interruption w ith a communication card.
nO
[Ignore]
(nO) : Detected fault ignored
YES [Fre e w heel] (YES) : Freew heel stop
Stt [Per STT] (Stt) : Stop according to configuration of [Type of stop] (Stt) page 173 , without fault tripping. In this case, the
fault relay does not open and the drive is ready to restart as soon as the detected fault disappears, according to the restart
conditions of the active command channel (for example, according to [2/3 wire control] (tCC) and [2 wire type] (tCt) page
125
if control is via the terminals). Configuring an alarm for this detected fault is recommended (assigned to a logic output, for
example) in order to indicate the cause of the stop
LFF [Fallback s pd] (LFF) : Change to fallback speed, maintained as long as the detected fault persists and the run command has
not been removed (1)
rLS
[Spd m aint.]
(rLS) : The drive maintains the speed being applied w hen the detected fault occurred, as long as the detected
fault is present and the run command has not been removed (1)
rMP [Ram p s top] (rMP) : Stop on ramp
FSt
[Fas t s top] (FSt) : Fast stop
dCI
[DC inje ction]
(dCI) : DC injection stop. This type of stop cannot be used w ith certain other functions. See table on page 163
COL [CANopen fault mgt] [Fre e w heel]
(YES)
nO
WARNING
LOSS OF CONTROL
If this param eter is s et to [Ignore] (nO) , CANopen com m unication m onitoring is dis abled.
•
Only us e this s etting after a thorough ris k as s essment in com pliance with all regulations and s tandards
that apply to the device and to the application.
•
Only us e this s etting for tes ts during commissioning.
•
Verify that com m unication m onitoring has been re-enabled before com pleting the com missioning
procedure and perform ing the final com missioning tes t.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Behavior of the drive in the event of a communication interruption w ith integrated CANopen®.
[Ignore]
(nO) : Detected fault ignored
[Fre e w heel] (YES) : Freew heel stop
[Per STT] (Stt) : Stop according to configuration of [Type of stop] (Stt) page 173 , without fault tripping. In this case, the
fault relay does not open and the drive is ready to restart as soon as the detected fault disappears, according to the restart
conditions of the active command channel (for example, according to
[2/3 wire control] (tCC) and [2 wire type] (tCt) page
125
if control is via the terminals). Configuring an alarm for this detected fault is recommended (assigned to a logic output, for
example) in order to indicate the cause of the stop.
[fallback s pd]
(LFF) : Change to fallback speed, maintained as long as the detected fault persists and the run command has
not been removed (1)
[Spd m aint.]
(rLS) : The drive maintains the speed being applied w hen the detected fault occurred, as long as the detected
fault is present and the run command has not been removed (1)
[Ram p s top] (rMP) : Stop on ramp
[Fas t s top]
(FSt) : Fast stop
[DC inje ction]
(dCI) : DC injection stop. This type of stop cannot be used w ith certain other functions. See table on page 165 .
YES
Stt
LFF
rLS
rMP
FSt
dCI
SLL
[Modbus fault mgt]
[Fre e w heel] (YES)
WARNING
LOSS OF CONTROL
If this param eter is s et to
[Ignore]
(nO) , Modbus com m unication m onitoring is disabled.
•
Only us e this s etting after a thorough ris k as s essment in com pliance with all regulations and s tandards
that apply to the device and to the application.
•
Only us e this s etting for tes ts during commissioning.
•
Verify that com m unication m onitoring has been re-enabled before com pleting the com missioning
procedure and perform ing the final com missioning tes t.
Failure to follow these instructions can result in death, serious injury, or equipment damage.
Parameters described in this page can be accessed by:
DRI- > CONF > FULL > FLT- > CLL-