manualshive.com logo in svg

Basler BE1-CDS240, Instruction Manual

Share
Download
Basler BE1-CDS240 Instruction Manual Download Page 80

The setting group control function has four logic variable outputs, SG0, SG1, SG2, and SG3. The 
appropriate variable is asserted when each setting group is active. These logic variables can be used in 
programmable logic to modify the logic based upon which setting group is active. For example, it may be 
desired for the 51P to trip the low side breaker through OUT2 under normal conditions, but to trip the 86T 
lockout relay through OUT1 when in Setting Group 3. The logic for OUT1 would include the term 
51PT

SG3 so that 51PT only actuates OUT1 when SG3 is asserted.  

The setting group control function also has an alarm output variable SGC (Setting Group Changed). This 
output is asserted whenever the relay switches from one setting group to another. The SGC alarm bit is 
asserted for the SGCON time setting. This output can be used in the programmable alarms function if it is 
desired to monitor when the relay changes to a new setting group. See Section 6, 

Reporting and Alarm 

Functions, Alarms Function, 

for more information on using alarm outputs.  

The SGCON time setting also serves to provide anti-pump protection to prevent excessive changing 
between groups. Once a change in active group has been made, another change cannot take place for 
two times the SGCON setting.  

When the relay switches to a new setting group, all functions are reset and initialized with the new 
operating parameters. The setting change occurs instantaneously so at no time is the relay off line. The 
active setting group is saved in nonvolatile memory so that the relay will power up using the same setting 
group as it was using when it was powered down. To prevent the relay from changing settings while a 
fault condition is in process, setting group changes are blocked when the relay is in a picked-up state. 
Since the relay is completely programmable, the fault condition is defined by the pickup logic expression 
in the fault reporting functions. See Section 

6, Reporting and Alarm Functions, Fault Reporting,

 for more 

information.  

The selection of the active setting group provided by this function block can also be overridden. When the 
logic override is used, a setting group is made active and the relay stays in that group regardless of the 
state of the automatic or manual logic control conditions.   

BESTlogic Settings for Setting Group Control 

BESTlogic settings are made from the 

BESTlogic Function Element

 screen in BESTCOMS. The 

BESTCOMS screen used to select BESTlogic settings for the 

Setting Group Selection

 function is 

illustrated in Figure 4-2. To open the 

BESTlogic Function Element

 screen for 

Setting Group Selection

, 

select 

Setting Group Selection

 from the 

Screens

 pull-down menu. Then select the 

BESTlogic

 button in 

the lower left hand corner of the screen. Alternately, settings may be made using the SL-GROUP ASCII 
command. 

 

Figure 4-2. BESTlogic Function Element Screen, Setting Group Selection 

4-2 

BE1-CDS240 Protection and Control 

9365200990 Rev F 

Summary of Contents for BE1-CDS240





































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands