Altigen AltiWare ACM 5.1 Administration Manual Download Page 94 | Manualshive

Page: 94 / 454

background image

Chapter 5: Gateway Management

80

AltiWare ACM 5.1 Administration Manual

Note:

AltiWare and AltiGateway servers have to be on the same LAN. Connecting an
AltiGateway from a remote site to the AltiWare site through a WAN connection is
not supported. The WAN network delay and latency may cause synchronization
signal failure between AltiWare and the AltiGateway.

Managing AltiGateways

Whether you are using multiple gateways or one gateway, you will perform gateway
management functions in the Gateway Management window. See “Minimum System
Requirements” on page 21 for system requirements for multiple gateways. If your
system does not meet these requirements, do not attempt to attach a second gateway
to it.
The Gateway Management window lists each gateway in your system, its number, name
and password, IP address, status, country, and how many IP phones are assigned to the
gateway as a home gateway. Use this window to:

•

Add and delete a gateway

•

Attach and detach a gateway

•

Change a gateway name, IP address, password, country

•

Set TDM Bus mode for a gateway

•

Set CT-Bus clock for a gateway

•

Set whether the gateway is in service or out of service

To open the Gateway Management window, select
System > Gateway Management.

Figure 2. Gateway Management window

«
...
92
93
94
95
96
...
»

Summary of Contents for AltiWare ACM 5.1







































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACM 5.1

Brand: NEC Pages: 4

WJ-ND300 Administrator Console

Brand: Panasonic Pages: 27

4116 - SCX B/W Laser

Brand: Samsung Pages: 14

2252W - Printer - B/W

Brand: Samsung Pages: 10

COLFUSION MX 7 - INSTALLING AND USING COLDFUSION...

Brand: MACROMEDIA Pages: 72

MAIL - BROWSING SMARTPHONE

Brand: Blackberry Pages: 25

8.5 ANTI-VIRUS - LINUX-FREEBSD REV 85.2

Brand: AVG Pages: 234

Brand: Nokia Pages: 29

Brand: Nokia Pages: 29

Brand: Nokia Pages: 35

NPS6113000 - Secure Access System

Brand: Nokia Pages: 48

N73 - Smartphone 42 MB

Brand: Nokia Pages: 354

N73 - Smartphone 42 MB

Brand: Nokia Pages: 265

Network Voyager

Brand: Nokia Pages: 700

Total Control Mobile

Brand: URC Pages: 14

Brand: AMX Pages: 16

Brand: GRASS VALLEY Pages: 2

Brand: GRASS VALLEY Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands