manualshive.com logo in svg

Altigen AltiWare ACM 5.1, Administration Manual

The Altigen AltiWare ACM 5.1 Administration Manual is a comprehensive guide for managing your communication system. Download this manual for free from our website and access detailed instructions on configuring settings, troubleshooting issues, and optimizing performance. Get the most out of your product with this essential resource.

Share
Download
background image

Chapter 25:  Enterprise VoIP Network Management

AltiWare ACM 5.1 Administration Manual 327

Configuration Buttons

•

Servers button displays the VoIP domain name, servers in the system, and server 
ID length. Lets you add/remove servers and change the VoIP domain master. 
Displays the configuration and informational tabs listed in the next section.

•

Codec button lets you configure individual codec profiles—silence suppression, 
codec, jitter buffer range, RTP packet length, DTMF delivery, and enable/disable SIP 
early media.

•

User button displays information about extensions in the VoIP domain and lets you 
change an extension to global or local and relocate an extension. 

•

Global LCR button lets you add E.164 number patterns and specify source and 
target sites.

Tabs Displayed with the Servers Button

•

Information tab displays information about the selected site.

•

IP Networks tab defines IP networks and the bandwidth information for an AltiWare 
site. Bandwidth usage control for Internet and intranet can be set up here. If the 
bandwidth usage exceeds the maximum setting, the call will not be established. 

•

IP Dialing Table tab defines the IP dialing table for an AltiWare site. Specified 
information here includes a codec profile and a protocol (SIP or H323) for the 
communication from this site to the selected site.

•

IP Codec tab lets you specify an inter-gateway codec and define IP device ranges 
to which you can assign a codec profile.

•

Number Plan tab displays the number plan information that is set up in AltiWare 
Administrator, System Configuration window, Number Plan tab.

Changing the AltiEnterprise Manager Password

Only a person with DomainAdmin rights can change the AltiEnterprise Manager 
password. To change the password, click the Password button at the top of the 
AltiEnterprise Manager window. The following dialog box opens:

Enter the old password, and the new password. Confirm the password, and click OK.

Setting VoIP Codec Profiles

The codec setting in AltiWare 5.1 is profile-based. For different IP addresses and 
protocols, a different preferred codec can be used. Each codec profile can have its own 
codec (G.711, G.723, G.729), packet length, and jitter buffer. The codec profile can be 
assigned to connectivity with a remote server, IP phone or other VoIP device.

Summary of Contents for AltiWare ACM 5.1







































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACM 5.1

MACROMEDIA BREEZE-MANAGING EXTERNAL BREEZE REPORTS Manual preview
BREEZE-MANAGING EXTERNAL BREEZE REPORTS
Brand: MACROMEDIA Pages: 18
Extreme Networks EPICenter 4.1 Software Installation Manual preview
EPICenter 4.1
Brand: Extreme Networks Pages: 546
Extreme Networks ExtremeWare 7.5 Command Reference Manual preview
ExtremeWare 7.5
Brand: Extreme Networks Pages: 2546
Am Mini-SOHO Quick Setup Manual preview
Mini-SOHO
Brand: Am Pages: 14
OCZ ATV-TURBO - WINDOWS 98 Installation Manual preview
ATV-TURBO - WINDOWS 98
Brand: OCZ Pages: 5
SSI TROPOS SUPERSEARCH 2.4.0.000 Installation Manual preview
TROPOS SUPERSEARCH 2.4.0.000
Brand: SSI Pages: 8
AMD AMD-8151 HyperTransport AGP3.0 Revision preview
AMD-8151 HyperTransport AGP3.0
Brand: AMD Pages: 16
SMART SMART Notebook SE Installation Manual preview
SMART Notebook SE
Brand: SMART Pages: 20
APPLIED ACOUSTICS SYSTEMS STRINGSTUDIO User Manual preview
STRINGSTUDIO
Brand: APPLIED ACOUSTICS SYSTEMS Pages: 70
Intel Solid-State Drive Toolbox User Manual preview
Solid-State Drive Toolbox
Brand: Intel Pages: 32
AMX AXWire Instruction Manual preview
AXWire
Brand: AMX Pages: 16
GRASS VALLEY MEDIAEDGE3 DCM Datasheet preview
MEDIAEDGE3 DCM
Brand: GRASS VALLEY Pages: 2
GRASS VALLEY K2 Dyno PA Configuration Manual preview
K2 Dyno PA
Brand: GRASS VALLEY Pages: 60
Zio Interactive Cassiopeia Pocket PC User Manual preview
Cassiopeia Pocket PC
Brand: Zio Interactive Pages: 17
KAPERSKY ANTI-VIRUS 5.0 - FOR LOTUS NOTES-DOMINO User Manual preview
ANTI-VIRUS 5.0 - FOR LOTUS NOTES-DOMINO
Brand: KAPERSKY Pages: 137
Campbell PONDVIEW 4.0 Instruction Manual preview
PONDVIEW 4.0
Brand: Campbell Pages: 38
Campbell RTDM Instruction Manual preview
RTDM
Brand: Campbell Pages: 22
FieldServer FS-8704-12 Manual preview
FS-8704-12
Brand: FieldServer Pages: 26

Brands by name

Popular brands

Load more brands