Altigen AltiWare ACM 5.1 Administration Manual Download Page 435 | Manualshive

Page: 435 / 454

background image

Appendix B: Required Service Parameters

AltiWare ACM 5.1 Administration Manual 421

Service Parameters/Request Information for PRI

To subscribe to PRI service, certain parameters are required to establish service. The
information provided below identifies the recommended and supported parameters for
PRI service. When ordering PRI service, provide the following service request
information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for PRI with Voice

Switch Type:

•

5ESS (recommended)

•

DMS (recommended)

•

NI-2 (recommended)

•

4ESS

•

MEGACOMM

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

Physical Termination:

•

RJ-48X or RJ-48C

Wire:

•

4 wires

PRI Channel Assignment

D Channels Assignment—24th channel (channel ID 23)

Note:

AltiWare ACC/ACM can configure any channel in a PRI span to be the D
channel. The default setting is the last channel. Every span should select a D
channel within the span. Shared D channel (NFAS) or back up D channel is
not supported.

Hunting—Most Idle, Least Idle, Ascend, Descend
DNIS Digits—can be 3 to 10 digits

CSU/DSU Requirements

The CSU (channel service unit) is a device used to connect a digital trunk line coming in
from the phone company to the PBX. A CSU can terminate signals, repeat signals, and
respond to loopback commands sent from the central office.

«
...
433
434
435
436
437
...
»

Summary of Contents for AltiWare ACM 5.1







































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACM 5.1

Brand: Extreme Networks Pages: 546

ExtremeWare 7.5

Brand: Extreme Networks Pages: 2546

G4 PANELPREVIEW V1.2

Brand: AMX Pages: 16

Phaser 340 Installer

Brand: Xerox Pages: 2

App for Android

Brand: TomTom Pages: 58

Brand: Philips Pages: 18

Brand: NETGEAR Pages: 282

CERTIFICATE SYSTEM 7.3 - ADMINISTRATION

Brand: Red Hat Pages: 554

Brand: Nikon Pages: 12

Brand: TROY Group Pages: 10

Over Loud Guitar FX Plug-in Suite

Brand: Focusrite Pages: 8

AUTOCAD P AND ID 2010

Brand: Autodesk Pages: 4

657B1-000110-S001 - Maya - Mac

Brand: Autodesk Pages: 5

18507-051452-9325 - UPG ARCH DESKTOP 2007

Brand: Autodesk Pages: 104

DVDMovieFactory

Brand: Ulead Pages: 50

Brand: Quantum Pages: 304

Brand: Paradyne Pages: 24

Brand: Waves Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands