Altigen AltiWare ACM 5.1 Administration Manual Download Page 344 | Manualshive

Page: 344 / 454

background image

Chapter 25: Enterprise VoIP Network Management

330

AltiWare ACM 5.1 Administration Manual

Assigning Codec Profiles to IP Addresses

You can specify what codec profile to use when connecting to the following VoIP devices:

•

IP phones on the LAN

•

a remote IP phone over WAN

•

a remote AltiGen system over WAN

•

SIP Trunk service provider over WAN

•

multiple AltiGateways on the LAN

The codec profile assigned in the IP Device Range table (shown below) supersedes the
codec profile defined in the IP dialing table if the IP address is duplicated in both tables.

G.711/G.723/G.729
Jitter Buffer Range
(ms)

Indicates the delay, in milliseconds, used to buffer
G.711/G.723/G.729 voice packets received from the
IP network. Voice packets sent over the IP network
may incur different delays due to network load or
congestion. The jitter buffer helps to smooth out the
delay variation in the arriving voice packets and
maintain voice quality at the receiving end.
The default values for the jitter buffer for G.711 is 10
min. to 100 max milliseconds.
The default values for the jitter buffer for G.723 is 30
min. to 480 max milliseconds.
The default values for the jitter buffer for G.729 is 10
min. to 480 max milliseconds.

G.711 RTP Packet
Length (ms)

Lets you configure the length of the RTP packets for
G.711 in milliseconds. The RTP packet length can be
set to 10, 20 or 30 milliseconds. The smaller the
packet length, the larger the bandwidth required.

G.729 RTP Packet

Length (ms)

Lets you configure the length of the RTP packets for
G.729 in milliseconds. The RTP packet length can be
set to 10, 20 or 30 milliseconds.

DTMF Delivery
(Applies to SIP protocol
only)

Default—If SIP INFO is used to deliver DTMF.
RFC 2833—The DTMF pay load is embedded with
RTP. Most 3rd-party SIP gateways support this
standard. Applies to SIP TRUNK only.
In band—If deliver DTMF tone over the voice band.
It’s not reliable over G.711 codec and will not work
over G.729/G.723 codec

SIP Early Media
(Applies to SIP protocol
and SIP trunk only)

SIP Early Media allows two SIP devices to
communicate before a SIP call is actually
established. It is important for interoperability with
the SIP trunk carrier’s PSTN gateway. If SIP Early
Media is not checked, the caller may not hear the
exact ringback tone provided by the CO (the caller
may not hear any ringback tone at all).

Parameter

Description

«
...
342
343
344
345
346
...
»

Summary of Contents for AltiWare ACM 5.1







































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACM 5.1

DL385 - ProLiant - G5

Brand: XenSource Pages: 313

Brand: Halcro Pages: 12

8.5 ANTI-VIRUS - LINUX-FREEBSD REV 85.2

Brand: AVG Pages: 234

Brand: Brocade Communications Systems Pages: 47

FastTrak SX Series Version 4.4

Brand: Promise Technology Pages: 102

PARTNER ACS R5.0

Brand: Avaya Pages: 32

READIRIS PRO 12

Brand: I.R.I.S. Pages: 10

DSP/BIOS Real-Time Analysis

Brand: Texas Instruments Pages: 29

Formidable mOByDic 3210 Series

Brand: Fiat Pages: 17

CONTRIBUTE 3 - DEPLOYING AND PUBLISHING...

Brand: MACROMEDIA Pages: 66

Retail Data Warehouse

Brand: Oracle Pages: 35

Oracle7 Server 7.3

Brand: Oracle Pages: 202

Terminal Emulation TN5250

Brand: IBM Pages: 51

ANTI-VIRUS 5.6 - FOR NOVELL NETWARE

Brand: KAPERSKY Pages: 130

Brand: ICP Pages: 8

C6 Easy Imaging

Brand: Clickfree Pages: 24

NBX V3000 Analog

Brand: 3Com Pages: 4

SuperStack II 3300 FX

Brand: 3Com Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands