Altigen AltiWare ACM 5.1 Administration Manual Download Page 37 | Manualshive

Page: 37 / 454

background image

Chapter 2: Software Installation & License Registration

AltiWare ACM 5.1 Administration Manual 23

Preparation for Installation

Before you start installing AltiWare, you need the following:

•

Windows Update—Make sure your server has the recommended Windows Service
Pack or Update.

•

AltiWare 5.1 CD ROM—The AltiWare CD ROM that contains the AltiWare 5.1
programs.

•

AltiWare latest update—Check to see if there is an Update available to the
AtliWare 5.1 Release.

•

System Key—The system key is a DB-25 parallel port hardware security device that
allows the software to run ONLY when that system key is attached to the parallel
port of the server that AltiWare is running on. (By special order, your system key
may be a USB key.)

•

Software license key—A 20-digit key located on the front of the End User License
Agreement. The following table lists all licenses used in AltiWare 5.1.

Table 1. AltiWare ACC/ACM 5.1 License Summary

License

Type

License

Model

Supported AltiWare Software Version

ACC 5.1

ACM 5.1

Server Base
License

Per System

•

Fresh Install

•

Upgrade

•

Upgrade

•

Migrate

Station License

Per Activated

Extension

YES

YES

Agent Seat

Per concurrent login
(Single agent
logged into multiple
WGs will only take
one license)

ACC Agent Seat

ACM Agent Seat

AltiView

Per concurrent login

YES

YES

AltiConsole

Per concurrent login

YES

YES

AltiAgent

Per concurrent login

YES

YES

AltiSupervisor

Per concurrent login

YES

YES

IPTalk

Per concurrent login

YES

YES

SIP Trunk

Per activated SIP

trunk

YES

YES

Centralized
Recording

Per Session

NO

YES

Advanced Call
Router

Per System

NO

YES

AltiReport

Per System

NO

YES

VRManager

Per System

NO

YES

AltiWeb

Per System

NO

YES

SDK

Per Session

NO

YES

«
...
35
36
37
38
39
...
»

Summary of Contents for AltiWare ACM 5.1







































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACM 5.1

MAIL - BROWSING SMARTPHONE

Brand: Blackberry Pages: 25

Quality Monitoring

Brand: Nortel Pages: 22

CONTRIBUTE-USING CONTRIBUTE

Brand: MACROMEDIA Pages: 214

Brand: Mackie Pages: 8

Blank Media LYT1015

Brand: JVC Pages: 22

Brand: JVC Pages: 43

JLIP VIDEO CAPTURE

Brand: JVC Pages: 56

GR-DVL500U - Digital Camcorder

Brand: JVC Pages: 72

GZMG27US - Everio Camcorder - 680 KP

Brand: JVC Pages: 72

GZ-MG77U - Everio Camcorder - 2.18 MP

Brand: JVC Pages: 72

Digital Photo Navigator ImageMixer with VCD LYT1116-001A

Brand: JVC Pages: 50

GZMG21US - Everio Camcorder - 680 KP

Brand: JVC Pages: 72

WISE INSTALLATION EXPRESS 7.0 SP2

Brand: Symantec Pages: 50

Scarbee Clavinet & Piano

Brand: Native Instruments Pages: 24

Brand: Palm Pages: 22

Brand: 10ZiG Technology Limited Pages: 125

MapCreate Canada 6.3

Brand: LEI Extras Pages: 1

Brand: FieldServer Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands