manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 339

Current APS Status : OK

Multi-Chassis APS  : No

Neighbor           : 0.0.0.0

Control link state : N/A

Advertise Interval : 1000 msec              Hold time            : 3000 msec

Mode mismatch Cnt  : 0                      Channel mismatch Cnt : 0

PSB failure Cnt    : 0                      FEPL failure Cnt     : 0

===============================================================================

B:Dut-B#

B:Dut-E# show aps aps-1 detail

===============================================================================

APS Group: aps-1

===============================================================================

Description        : APS Group

Group Id           : 1                      Active Circuit       : N/A

Admin Status       : Down                   Oper Status          : Down

Working Circuit    : N/A                    Protection Circuit   : N/A

Switching-mode     : Bi-directional         Switching-arch       : 1+1

Revertive-mode     : Non-revertive          Revert-time (min)    :

Rx K1/K2 byte      : N/A

Tx K1/K2 byte      : N/A

Current APS Status : OK

Multi-Chassis APS  : No

Neighbor           : 0.0.0.0

Control link state : N/A

Advertise Interval : 1000 msec              Hold time            : 3000 msec

Mode mismatch Cnt  : 0                      Channel mismatch Cnt : 0

PSB failure Cnt    : 0                      FEPL failure Cnt     : 0

===============================================================================

B:Dut-E#

show aps 

on protect MC-APS node:

B:Dut-E# show aps 

==================================================================================

APS Group Info

==================================================================================

Interface Admin  Oper    MC-Ctl   Work      Prot       Active     Tx/Rx            

                 State   State    State     Circuit    Circuit    Circuit K1 Byte          

----------------------------------------------------------------------------------

aps-20    Up     Up      N/A      3/1/1     3/1/2      3/1/1      PC-Tx:  No-Req    

==================================================================================

B:Dut-E# 

B:Dut-E# show aps aps-30 detail

===============================================================================

APS Group: aps-30

===============================================================================

Description        : APS Group

Group Id           : 30                     Active Circuit       : N/A        

Admin Status       : Up                     Oper Status          : Up         

Working Circuit    : N/A                    Protection Circuit   : 2/2/2      

Switching-mode     : Bi-directional         Switching-arch       : 1+1        

Revertive-mode     : Non-revertive          Revert-time (min) :            

Rx K1/K2 byte      : 0x00/0x05 (No-Req on Protect)                            

Tx K1/K2 byte      : 0x00/0x05 (No-Req on Protect)                            

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

NEC Univerge SV8100 System Configuration Manual preview
Univerge SV8100
Brand: NEC Pages: 44
ICP DAS USA ET-7000 series Quick Start Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 14
ICP DAS USA I-2533 User Manual preview
I-2533
Brand: ICP DAS USA Pages: 25
ICP DAS USA ET-2200 Series Manual preview
ET-2200 Series
Brand: ICP DAS USA Pages: 15
ICP ZT-2550 Quick Start Manual preview
ZT-2550
Brand: ICP Pages: 14
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Brand: Quantum Pages: 20
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
Axis AXIS P1354 Installation Manual preview
AXIS P1354
Brand: Axis Pages: 104
MikroTik RouterBOARD Groove Quick Setup Manual And Warranty Information preview
RouterBOARD Groove
Brand: MikroTik Pages: 4
NETGEAR AC1450 Installation Manual preview
AC1450
Brand: NETGEAR Pages: 14
bintec elmeg RM7000 Installation Manual preview
RM7000
Brand: bintec elmeg Pages: 33
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
ZyXEL Communications Dimension ES-3124 User Manual preview
Dimension ES-3124
Brand: ZyXEL Communications Pages: 228
Tandberg Data SUPERLOADER DLT MAGAZINE Quick Start Manual preview
SUPERLOADER DLT MAGAZINE
Brand: Tandberg Data Pages: 6
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101

Brands by name

Popular brands

Load more brands