manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Show Commands

Page 338

7750 SR OS Interface Configuration Guide

Sample Output

show aps

 on a working multi-chassis APS node:

B:Dut-B# show aps aps-1

===============================================================================

APS Group Info

===============================================================================

Interface Admin  Oper   MC-Ctl  Work      Prot      Active    Tx/Rx

          State  State  State   Circuit   Circuit   Circuit   K1 Byte

-------------------------------------------------------------------------------

aps-1     Down   Down   N/A     N/A       N/A       N/A       N/A

===============================================================================

B:Dut-B#

B:Dut-B# show aps aps-30 detail

===============================================================================

APS Group: aps-1

===============================================================================

Description        : APS Group

Group Id           : 1                      Active Circuit       : N/A

Admin Status       : Down                   Oper Status          : Down

Working Circuit    : N/A                    Protection Circuit   : N/A

Switching-mode     : Bi-directional         Switching-arch       : 1+1

Revertive-mode     : Non-revertive          Revert-time (min)    :

Rx K1/K2 byte      : N/A

Tx K1/K2 byte      : N/A

Switchover sec-

onds

Displays the cumulative Protection Switching Duration (PSD) time in 
seconds. 
For a working channel, this is the cumulative number of seconds that 
service was carried on the protection line. 
For the protection line, this is the cumulative number of seconds that the 
protection line has been used to carry any working channel traffic. This 
information is only valid if revertive switching is enabled. 

Signal Degrade 

Cnt

Displays the number of times the signal was degraded.

Signal Failure 

Cnt

Displays the number of times the signal failed.

Last Switch Cmd

Reports the last switch command that was performed on a circuit.

Last Exercise 

Result

The result of the last exercise request on a circuit.

Neighbor address

Displays the neighbor IP address.

Advertise Inter-

val

Displays the advertise interval.

Hold time

Displays the hold time.

Label

Description  (Continued)

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Sun Microsystems Ray 3 Plus Client Getting Started Manual preview
Ray 3 Plus Client
Brand: Sun Microsystems Pages: 6
Patton electronics 4520 Specification Sheet preview
4520
Brand: Patton electronics Pages: 2
Patton electronics 4520 Getting Started Manual preview
4520
Brand: Patton electronics Pages: 86
Patton electronics 2888 Getting Started Manual preview
2888
Brand: Patton electronics Pages: 51
3Com 3C13886 - Router OC-3 ATM SML Flexible Interface... Installation Manual preview
3C13886 - Router OC-3 ATM SML Flexible Interface...
Brand: 3Com Pages: 171
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Garland INT10G10SP2 User Manual preview
INT10G10SP2
Brand: Garland Pages: 6
CSS SafetyNet Quick Install Manual preview
SafetyNet
Brand: CSS Pages: 2
Vaisala TERMBOX-1200 User Manual preview
TERMBOX-1200
Brand: Vaisala Pages: 32
Hornington AirStation WHR-G300N Settings preview
AirStation WHR-G300N
Brand: Hornington Pages: 6
Allnet ALL1682504 Quick Installation preview
ALL1682504
Brand: Allnet Pages: 12
Telebyte 458-LM-E2-36 Quick Start Manual preview
458-LM-E2-36
Brand: Telebyte Pages: 19
National Instruments NI WLS/ENET-9163 User Manual preview
NI WLS/ENET-9163
Brand: National Instruments Pages: 36
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Cabletron Systems SmartSwitch 8-slot User'S Reference Manual preview
SmartSwitch 8-slot
Brand: Cabletron Systems Pages: 150
Delta Electronics LonWorks Communication Module LN-01 Instruction Sheet preview
LonWorks Communication Module LN-01
Brand: Delta Electronics Pages: 1
Cabletron Systems SmartSTACK ELS100-24TXM Installation And User Manual preview
SmartSTACK ELS100-24TXM
Brand: Cabletron Systems Pages: 117

Brands by name

Popular brands

Load more brands