Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 94 | Manualshive

Page: 94 / 444

Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 94

Port Features

Page 94

7750 SR OS Interface Configuration Guide

Deploying Preprovisioned Components

When a line card/MDA is installed in a preprovisioned slot, the device detects discrepancies
between the preprovisioned card and MDA type configurations and the types actually installed.
Error messages display if there are inconsistencies and the card will not initialize.

When the proper preprovisioned card and MDA are installed into the appropriate chassis slot,
alarm, status, and performance details will display.

«
...
92
93
94
95
96
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments