Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 118 | Manualshive

Page: 118 / 444

background image

Configuring Ports

Page 118

7750 SR OS Interface Configuration Guide

Configuring Channelized Ports

•

Configuring a Channelized DS3 Port on page 123

•

Configuring a Channelized OC-12-SFP Port on page 126

•

Configuring a Channelized Any Service Any Port (ASAP) OC3-SFP Port on page 130

•

Configuring Cisco HDLC on a Channelized Port on page 133

When configuring channelized ports, the port ID is specified in different ways depending on the
MDA type and level of channelization. Ethernet ports cannot be channelized.

lists

channelization options available on the 7750 SR channelized MDAs and gives port ID syntax for
each.

Table 20: Channelization Options Available on the 7750 SR Channelized MDAs

Framing

Channelization/mapping option

Channelized MDAs Supporting

Services on the Port/Channel

599,040 kbits/s (clear channel OC12/STM-4)

SDH

STM4>AUG4>VC4-C4

None

SONET

OC12>STS12>STS12c SPE

None

139,264 kbits/s ñ 149,760 Kbits/s (clear channel STS-3/STM-1 or STS-3/STM-1 channel within STS12-STM4

SDH

STM4>AUG4>AUG1>VC4

m4-choc3-as

SONET

OC12>STS12>STS3c SPE

m4-choc3-as

44,763 kbits/s (DS3 or sub-DS3 port or a channel)

SDH

STM4>AUG4>AUG1>VC4>TUG3>VC3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SDH

STM4>AUG4>AUG1>VC3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SONET

OC12>STS12>STS1 SPE

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SDH

STM4>AUG4>AUG1>VC4>TUG3>VC3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

«
...
116
117
118
119
120
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: 3Com Pages: 48

ADSL 2/2+ Router with USB Port ADE-3410v2

Brand: Planet Pages: 62

Brand: Genie Pages: 15

Brand: IDT Pages: 207

Brand: AMX Pages: 2

DiamondLink 3201

Brand: Patton Pages: 12

Ezi-SERVOII EtherCAT TO

Brand: Fastech Pages: 108

Brand: Global411 Pages: 15

Brand: MiWire Pages: 24

Brand: Unex Pages: 27

NetVanta Serial Dial Backup Interface Module (DIM) none

Brand: ADTRAN Pages: 2

Brand: ALIBI Pages: 232

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Altusen SN0100 Series

Brand: ATEN Pages: 178

Brand: Allied Telesis Pages: 19

Brand: Crestron Pages: 2

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands