manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 221

Discards                                               0                      0

Unknown Proto Discards                                 0                       

===============================================================================

A:NS044050253# 

For unprotected port these timer are different:

A:NS044050253# show port 2/2/2

===============================================================================

SONET/SDH Interface

===============================================================================

Description        : OC-48 SONET/SDH

Interface          : 2/2/2                  Speed                : oc48        

Admin Status       : up                     Oper Status          : up          

Physical Link      : Yes                    Loopback Mode        : none        

Single Fiber Mode  : No                                                        

APS Group          : none                   APS Role             : none        

Clock Source       : loop                   Framing              : sonet       

Last State Change  : 04/11/2007 14:53:53    Port IfIndex         : 37814272    

J0 String          : 0x01                   Section Trace Mode   : byte        

Rx S1 Byte         : 0x00                   Rx K1/K2 Byte        : 0x00/0x00   

Rx J0 String (Hex) : af 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00       

Cfg Alarm          : loc lrdi lb2er-sf slof slos                           

Alarm Status       :                                                       

Hold time up       : 500 milliseconds                                      

Hold time down     : 0 milliseconds        

                                

Transceiver Data

Transceiver Type   : SFP                                             

Model Number       : SFP-OC48-SR1                                    

Transceiver Code   : OC48 SR                                         

Laser Wavelength   : 1310                   Diag Capable         : yes         

Connector Code     : LC                     Vendor OUI           : 00:01:9c    

Manufacture date   : 2004/08/20 00:00:00    Media                : SONET/SDH   

Serial Number      : 6331000705                                      

Part Number        : CT2-MS1LBTD32Z2                                 

Optical Compliance*: 00:01:00:00:00:00:00:00                         

Link Len 9u        : 2 kms                  Link Len Cu          : 0 m         

Link Len 9u        : 20 * 100m              Link Len 62.5u       : 0 * 10m     

Link Len 50u       : 0 * 10m 

===============================================================================

Port Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Packets                                          3870094                6656408

Discards                                               0                      0

Unknown Proto Discards                                 0                       

===============================================================================

A:NS044050253# 

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
H3C CR16000-M Installation Manual preview
CR16000-M
Brand: H3C Pages: 116
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
KonNad SinoCon C2000-C2-SHK0401-BB1 User Manual preview
SinoCon C2000-C2-SHK0401-BB1
Brand: KonNad Pages: 12
Patton DiamondLink 3201 Quick Start Manual preview
DiamondLink 3201
Brand: Patton Pages: 12
Fastech Ezi-SERVOII EtherCAT TO User Manual preview
Ezi-SERVOII EtherCAT TO
Brand: Fastech Pages: 108
Global411 MS41p1 Quick Installation Manual preview
MS41p1
Brand: Global411 Pages: 15
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
Tripp Lite WEBCARDLX Owner'S Manual preview
WEBCARDLX
Brand: Tripp Lite Pages: 34
Chase Research IOLINK-130 Installation & Application Manual preview
IOLINK-130
Brand: Chase Research Pages: 114
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
TRENDnet TW100-W2plus Specifications preview
TW100-W2plus
Brand: TRENDnet Pages: 2
TRENDnet TE100-S2424V Specifications preview
TE100-S2424V
Brand: TRENDnet Pages: 2
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
Lindy Modular Fast Fiber Switch Converter MT-RJ Specifications preview
Modular Fast Fiber Switch Converter MT-RJ
Brand: Lindy Pages: 3
OST RuggedNet 10G/Si User Manual preview
RuggedNet 10G/Si
Brand: OST Pages: 8

Brands by name

Popular brands

Load more brands