manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 244

Configuration Commands

Page 244

7750 SR OS Interface Configuration Guide

egress

Context

config>port>ml-bundle>mlppp

Description

This command enables the context to configure egress MLPPP QoS profile parameters for the 
multilink bundle.

Default

none

ingress

Context

config>port>ml-bundle>mlppp

Description

This command enables the context to configure ingress MLPPP QoS profile parameters for the 
multilink bundle.

Default

none

qos-profile

Syntax

qos-profile 

profile-id

no qos-profile

Context

config>port>ml-bundle>mlppp>egress

Description

This command specifies the egress QoS profile to be used for the outgoing traffic over this MLPPP 
bundle.

The 

no

 form of the command removes the parameters from the configuration.

profile-id — 

Specifies the egress QoS profile to be used for the outgoing traffic over this MLPPP 

bundle. The value can only be modified if the bundle is shutdown.

Values

1 — 128

endpoint-discriminator

Syntax

endpoint-discriminator class

 {

ip-address

 | 

global-mac-address

} [

discriminator-id

 

discriminator-id

]

no endpoint-discriminator

Context

config>port>ml-bundle>mlppp

Description

This command configures the endpoint-discriminator class and ID. The port must be shutdown to 
modify command parameters.

The 

no

 form of the command removes the parameters from the configuration.

Parameters

class — 

Specifies the Link Control Protocol endpoint descriminator class field type.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands