Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download | Manualshive

Page: 186 / 444

background image

Configuration Commands

Page 186

7750 SR OS Interface Configuration Guide

Parameters

long-description-string —

The description character string. Strings can be up to 160 characters long

composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $,
spaces, etc.), the entire string must be enclosed within double quotes.

shutdown

Syntax

[

no

]

shutdown

Context

config>card
config>card>mda
config>port
config>port>sonet-sdh>path
config>port>tdm>ds1
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1
config>port>tdm>e1>channel-group
config>port>tdm>e3
config>port>multilink-bundle>ima>test-pattern-procedure
config>port>sonet-sdh>path>atm>ilmi
config>lag
config>port>ethernet>efm-oam
config>redundancy>multi-chassis>peer
config>redundancy>mc>peer>mc-lag
config>redundancy>mc>peer>mcr>ring
config>redundancy>mc>peer>mcr>node>cv
config>redundancy>multi-chassis>peer>sync

Description

This command administratively disables an entity. When disabled, an entity does not change, reset, or
remove any configuration settings or statistics.

The operational state of the entity is disabled as well as the operational state of any entities contained
within.

The

no

form of this command administratively enables an entity.

Special Cases

card —

The default state for a card is

no shutdown

.

mda —

The default state for a mda is

no

shutdown

.

lag —

The default state for a Link Aggregation Group (LAG) is

shutdown

.

port —

The default state for a port is

shutdown

.

path —

The default state for a SONET/SDH path is

shutdown

.

«
...
184
185
186
187
188
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: DataRemote Pages: 2

Brand: LAWO Pages: 154

Brand: IBM Pages: 32

Brand: TP-Link Pages: 2

Brand: E-Lins Pages: 9

Brand: ZyXEL Communications Pages: 2

Wisenet PRN-6400B4

Brand: Hanwha Techwin Pages: 14

Brand: Lucent Technologies Pages: 20

Brand: Techroutes Pages: 20

Brand: AirTies Pages: 28

Brand: JUMO Pages: 60

Brand: Maipu Pages: 19

PXI PXITM -1000

Brand: National Instruments Pages: 55

PacketMate 1000

Brand: General DataComm Pages: 20

Brand: Modecom Pages: 16

Brand: Ubiquiti Pages: 20

Brand: Milesight Pages: 15

TE100S8P - Fast Ethernet Switch

Brand: TRENDnet Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands