manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 231 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 231

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 231

ingress-rate

Syntax

ingress-rate 

sub-rate

no ingress-rate

Context

config>port>ethernet

Description

This command configures the maximum amount of ingress bandwidth that this port can receive.

The ingress-rate command is only valid for oversubscribed Ethernet MDAs. See 

Oversubscribed 

Ethernet MDAs on page 21

 for details.

The 

no

 form of this command returns the value to the default.

Default

no ingress-rate

Parameters

sub-rate — 

The egress rate in mbps.

Values

1 — 10000 mbps

lacp-tunnel

Syntax

[

no

] 

lacp-tunnel

Context

config>port>ethernet

Description

This command enables LACP packet tunneling for the Ethernet port. When tunneling is enabled, the 
port will not process any LACP packets but will tunnel them instead. The port cannot be added as a 
member to a LAG group.

The 

no

 form of the command disables LACP packet tunneling for the Ethernet port. 

Default

no lacp-tunnel

load-balancing-algorithm

Syntax

load-balancing-algorithm 

option

no load-balancing-algorithm

Context

config>port>ethernet
config>port>sonet-sdh>path
config>port>tdm>ds1>channel-group
config>port>tdm>ds3
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command specifies the load balancing algorithm to be used on this port. 

In the default mode, 

no load-balancing-algorithm

, the port inherits the global settings. The value is 

not applicable for ports that do not pass any traffic. 

The configuration of load-balancing-algorithm at logical port level has three possible values:

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments