manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 223 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 223

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 223

Values

1 — 10000 Mbps

Default

max

autonegotiate

Syntax

autonegotiate 

[

limited

]

[

no

]

 autonegotiate

Context

config>port>ethernet

Description

This command enables speed and duplex autonegotiation on Fast Ethernet ports and enables far-end 
fault indicator support on gigabit ports.

There are three possible settings for autonegotiation:

• “on” or enabled with full port capabilities advertised

• “off” or disabled where there are no autonegotiation advertisements

• “limited” where a single speed/duplex is advertised. 

When autonegotiation is enabled on a port, the link attempts to automatically negotiate the link speed 
and duplex parameters. If autonegotiation is enabled, the configured duplex and speed parameters are 
ignored. 

When autonegotiation is disabled on a port, the port does not attempt to autonegotiate and will only 
operate at the 

speed

 and 

duplex

 settings configured for the port. Note that disabling autonegotiation 

on gigabit ports is not allowed as the IEEE 802.3 specification for gigabit Ethernet requires 
autonegotiation be enabled for far end fault indication.

If the 

autonegotiate

 

limited

 keyword option is specified the port will autonegotate but will only 

advertise a specific speed and duplex. The speed and duplex advertised are the 

speed

 and 

duplex

 

settings configured for the port. One use for limited mode is for multispeed gigabit ports to force 
gigabit operation while keeping autonegotiation enabled for compliance with IEEE 801.3.

7750 SR OS requires that autonegotiation be disabled or limited for ports in a Link Aggregation 
Group to guarantee a specific port speed.

The 

no

 form of this command disables autonegotiation on this port.

Default

autonegotiate

Parameters

limited — 

The Ethernet interface will automatically negotiate link parameters with the far end, but 

will only advertise the speed and duplex mode specified by the Ethernet 

speed

 and 

duplex

 

commands.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments