manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 252 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 252

Configuration Commands

Page 252

7750 SR OS Interface Configuration Guide

SONET/SDH Port Commands

sonet-sdh

Syntax

sonet-sdh

Context

config>port

Description

This command enables access to the context to configure SONET/SDH ports. This context can only 
be used when configuring an OC-3, OC-12, OC-48 and OC-192 SONET/SDH ports on an 
appropriate MDA. 

The 10 Gigabit Ethernet LAN port also has SONET/SDH characteristics. However,  these 
characteristics are predetermined and not configurable.

clock-source 

Syntax

clock-source 

{

loop-timed | node-timed

}

Context

config>port>sonet-sdh

Description

This command configures the clock for transmitted data from either the internal clock or from a clock 
recovered from the line’s receive data stream. 

Note: When changing the clock source for a port on an OC-48 MDA, a brief transmit interruption can 
occur on all ports of that MDA. The following table show MDAs that support loop timing:

Parameters

loop-timed — 

The link recovers the clock from the received data stream.

node-timed — 

The link uses the internal clock when transmitting data.

MDA Supports

Loop Timed

Default

OC-192

Yes

loop-timed

OC-48

Yes

loop-timed

OC-12 No

node-timed

OC-3 No

node-timed

Channelized OC-12

Yes

loop-timed

Channelized OC-3

Yes

loop-timed

Channelized DS-3 

Yes

loop-timed

Channelized ASAP

Yes

loop-timed

Channelized ASAP

Yes

loop-timed

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments