Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 320

Page: 320 / 444

Show Commands

Page 320

7750 SR OS Interface Configuration Guide

Sample Output

ALA-1#

show chassis

=====================================================

Chassis Information

=====================================================

Name : Dut-D

Type : 7750 SR-7

Location :

Coordinates :

CLLI code :

Number of slots : 7

Number of ports : 19

Critical LED state : Off

Major LED state : Off

Minor LED state : Off

Base MAC address : 00:03:fa:14:cf:a7

Admin chassis mode : a

Oper chassis mode : a

Hardware Data

Part number : 3HE00186AAAA01

CLEI code :

Serial number : NS042450133

Manufacture date : 06172004

Manufacturing string :

Manufacturing deviations :

Time of last boot : 2007/04/11 09:37:51

Current alarm state : alarm cleared

Environment Information

Number of fan trays : 2

Number of fans : 4

Fan tray number : 1

Status : up

Speed : half speed

Fan tray number : 2

Status : up

Speed : half speed

Power Supply Information

Number of power supplies : 2

Power supply number : 1

Defaulted power supply type : none

Status : not equipped

Time of last

boot

The date and time the most recent boot occurred.

Current alarm

state

Displays the alarm conditions for the CCM.

Label

Description (Continued)

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands