manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 131 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 131

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 131

----------------------------------------------

A:ALA-A>config>port#

In the TDM E1 context, configure DS0 channel groups and their parameters.  For a DS1 channel-
group, up to 24 timeslots can be assigned (numbered 1— 24).  For an E1 channel-group, up to 31 
timeslots can be assigned (numbered 2 — 32). For ATM, all timeslots are auto-configured when a 
channel group gets created (there is no sub-E1 for ATM). ATM, Frame Relay and BCP-NULL 
encapsulation examples follow:

A:ALA-A>config>port>tdm# e1 1.1

A:ALA-A>config>port>tdm>e1# channel-group 1

A:ALA-A>config>port>tdm>e1>channel-group# timeslots 2

A:ALA-A>config>port>tdm>e1>channel-group# no shutdown

A:ALA-A>config>port>tdm>e1>channel-group# 

A:ALA-A>config>port>tdm>e1# no shutdown

A:ALA-A>config>port>tdm>e1# channel-group 2

A:ALA-A>config>port>tdm>e1>channel-group# timeslots 3

A:ALA-A>config>port>tdm>e1>channel-group# encap-type frame-relay

A:ALA-A>config>port>tdm>e1>channel-group# no shutdown

A:ALA-A>config>port>tdm>e1>channel-group# exit

A:ALA-A>config>port>tdm>e1# channel-group 3

A:ALA-A>config>port>tdm>e1>channel-group# timeslots 11,12

A:ALA-A>config>port>tdm>e1>channel-group# encap-type cisco-hdlc

A:ALA-A>config>port>tdm>e1>channel-group# no shutdown

A:ALA-A>config>port>tdm>e1>channel-group# exit

A:ALA-A>config>port>tdm>e1# no shutdown

A:ALA-A>config>port>tdm>e1# exit

A:ALA-A>config>port>tdm# e1 1.2

A:ALA-A>config>port>tdm>e1# no shutdown

A:ALA-A>config>port>tdm>e1# channel-group 1

A:ALA-A>config>port>tdm>e1>channel-group# encap-type atm

A:ALA-A>config>port>tdm>e1>channel-group# no shutdown

A:ALA-A>config>port>tdm>e1>channel-group# exit

A:ALA-A>config>port>tdm>e1# no shutdown

A:ALA-A>config>port>tdm# info

----------------------------------------------

        tdm

           ds3 1

                channelized e1

                no shutdown

            exit

           e1 1.1

                channel-group 1

                     timeslots 2

                     no shutdown

               exit

                channel-group 2

                    encap-type frame-relay

                    frame-relay

                    exit

                    timeslots 10

                    no shutdown

                exit

                channel-group 3

                    encap-type cisco-hdlc

                    cisco-hdlc

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments