Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 400

Page: 400 / 444

Show Commands

Page 400

7750 SR OS Interface Configuration Guide

Multilink Bundle Commands

multilink-bundle

Syntax

multilink-bundle

[

bundle-id

slot/mda

type

{

mlppp

ima-grp

}] [

detail

]

multilink-bundle

{

bundle-id

slot/mda

} [

ppp

ima

]

multilink-bundle

bundle-id

relations

multilink-bundle

bundle-id

ppp

[

multiclass

]

Context

show

Description

This comand displays multilink bundle information. An operator can display:

•

All bundles on the system/MDA or all bundles of a given type on the system by specifying
the value of type filter to be either mlppp or ima-grp.

•

Bundle specific information in summary (no detail option) or detailed format (detail option
specified) for one or more bundles

•

Protocol specific information (example PPP or IMA) for the specified bundle

•

ATM interface information for IMA groups see show port atm command for more details

Parameters

bundle-id —

Specifies the multilink (PPP or IMA) bundle to be associated with this IP interface. The

command syntax must be used as follows:

Syntax

: bundle-

type

slot/mda.bundle-num

bpgrp-

type

bpgrp-num

bundle

ppp

slot/mda.bundle-num

(Creates a multilink PPP bundle.)

bundle

ima

slot/mda.bundle-num

(Creates an IMA group bundle.)

bundle

: keyword

slot

IOM/MDA slot numbers

bundle-num

1 — 128

ppp —

Displays PPP bundle information.

ima, ima-grp —

Displays IMA-type groups.

mlppp —

Display MLPPP-type groups.

detail —

Provides detailed information.

relations —

Displays the working and protection bundles associated with this bundle-id.

Multilink Bundle Output —

The following table describes multilink bundle output fields.

Multilink Bundle Output Fields

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands