manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 406 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 406

Show Commands

Page 406

7750 SR OS Interface Configuration Guide

Multilink-Bundle IMA Output Fields

Sample Output

A:timetra-sim110# show multilink-bundle bundle-ima-1/1.2

===============================================================================

Bundle Summary

===============================================================================

Bundle               Type    Admin     Oper      Port      Min    Total/       

Id                           State     State     State     Links  Active Links 

-------------------------------------------------------------------------------

bundle-ima-1/1.2     ima     Down      Down      Link Up   1      1/0          

-------------------------------------------------------------------------------

Bundles : 1

===============================================================================

Label

Description  

BundleId

Displays the bundle ID number.

Type

Specifies the type of this multilink bundle.

mlppp — 

Indicates that the bundle is of type MLPPP.

ima — 

Indicates that the bundle is of type IMA group.

Admin State

ima — 

Indicates that the bundle is of type IMA group.

Down — 

The bundle is administratively down.

Oper State

Up — 

 The bundle is operationally up.

Down — 

The bundle is operationally down.

Port State

Displays the state level of the port.

none — 

Indicates that the port is either in its initial creation state or 

is just about to to be deleted.

ghost — 

No member links are configured as part of this bundle.

down — 

All member links are in “none”, “ghost”, or “down” state.

linkUp — 

At least one member link is in port state “link up” but the 

bundle protocol is not yet operationally up (due to bundle protocol still 
coming up. For example, due to insufficient number of member links 
in “link up” state yet or to bundle being shut down.

Up — 

Indicates that the bundle is ready to pass some kinds of traffic 

as the bundle protocol has come up (at least “minimum links” member 
links are in the port state up and the bundle protocol is up.)

Min Links

Minimum Links

Displays the minimum number of links that must be active for a bundle 
to be active. If the number of links drop below the given minimum 
then the multilink bundle will transition to an operation down state.)

Total/Active 

Links

Displays the total number of active links for the bundle.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments