manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Show Commands

Page 376

7750 SR OS Interface Configuration Guide

B:Dut-D# show port 2/2/1.1.1.1 atm detail

=============================================================================

ATM Info for 2/2/1.1.1.1

=============================================================================

Cell Mode             : UNI               Mapping            : Direct        

Configured VCs        : 16                Configured VPs     : 0             

Configured VTs        : 0                 Configured IFCs    : 0             

Configured minimum VPI: 0                                                    

Last Unknown VPI/VCI  : none 

=============================================================================

TC Sublayer Information

=============================================================================

TC Alarm State        : No Alarm          Number OCD Events  : 0             

HEC Errors (Dropped)  : 0                 HEC Errors (Fixed) : 0 

===============================================================================

ATM Bandwidth Info

===============================================================================

                     kbps      %                             kbps      %       

-------------------------------------------------------------------------------

Ingress CBR        : 0          0%      Egress CBR         : 0          0%     

Ingress RT-VBR     : 0          0%      Egress RT-VBR      : 0          0%     

Ingress NRT-VBR    : 0          0%      Egress NRT-VBR     : 0          0%     

Ingress UBR        : 0          0%      Egress UBR         : 0          0%     

-------------------------------------------------------------------------------

Ingress Total      : 0          0%      Egress Total       : 0          0%     

ATM Link Bandwidth : 1920 kbps     

Shaped Bandwidth   : 0 kbps           

===============================================================================

ATM Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Octets                                      228425945553           228453511542

Cells                                         4309923501             4310443614

Unknown VPI/VCI Cells                         4294967295                       

===============================================================================

AAL-5 Packet Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Packets                                       4302445396             4302705455

Dropped Packets                                        0                      0

CRC-32 Errors                                          0                       

===============================================================================

A:timetra-sim110#

B:Dut-D# show port 2/2/1.1.1.1 atm connections 

================================================================

ATM Connections, Port 2/2/1.1.1.1

================================================================

           Owner  Type     Ing.TD  Egr.TD  Adm  OAM         Opr                

----------------------------------------------------------------

0/100      SAP    PVC      101     201     up   up          up  

0/101      SAP    PVC      101     201     up   up          up  

0/102      SAP    PVC      101     201     up   up          up  

0/103      SAP    PVC      101     201     up   up          up  

0/104      SAP    PVC      101     201     up   up          up  

0/105      SAP    PVC      101     201     up   up          up  

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

D-Link DSL-2640BT Installation Manual preview
DSL-2640BT
Brand: D-Link Pages: 12
GE MDS SD Series Setup Manual preview
MDS SD Series
Brand: GE Pages: 4
Xantrex C12 Owner'S Manual preview
C12
Brand: Xantrex Pages: 8
G-Technology G-DRIVE ev ATC Product Manual preview
G-DRIVE ev ATC
Brand: G-Technology Pages: 35
Matrix Switch Corporation MSC-5-3232 Product Manual preview
MSC-5-3232
Brand: Matrix Switch Corporation Pages: 61
Paradyne Comsphere 3510 User Manual preview
Comsphere 3510
Brand: Paradyne Pages: 85
Supermicro SC836 X9 User Manual preview
SC836 X9
Brand: Supermicro Pages: 24
Supero 6027R-E1R12N User Manual preview
6027R-E1R12N
Brand: Supero Pages: 112
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Idis DR-6316PS-S Quick Manual preview
DR-6316PS-S
Brand: Idis Pages: 16
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
RTS AIO-8 Drawings Manual preview
AIO-8
Brand: RTS Pages: 3
Multi-Link Power Stone Programming Manual preview
Power Stone
Brand: Multi-Link Pages: 31
MicroNova O047 Technical Installation Manual preview
O047
Brand: MicroNova Pages: 113
Manson Engineering Industrial SBC-6108 User Manual preview
SBC-6108
Brand: Manson Engineering Industrial Pages: 10
InHand IR615-S Series User Manual preview
IR615-S Series
Brand: InHand Pages: 69

Brands by name

Popular brands

Load more brands