manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Show Commands

Page 328

7750 SR OS Interface Configuration Guide

===============================================================================

Slot      Provisioned         Equipped            Admin      Operational       

          Card-type           Card-type           State      State             

-------------------------------------------------------------------------------

A         sfm-400g            sfm-200g            up         up/standby        

BOF last modified                 : N/A                                        

Config file version               :                                            

Config file last modified         : N/A                                        

Config file last saved            : N/A                                        

CPM redundancy status             : standby ready                              

Flash - cf1:

    Administrative State          : up                                         

    Operational state             : not equipped                               

Flash - cf2:

    Administrative State          : up                                         

    Operational state             : not equipped                               

Flash - cf3:

    Administrative State          : up                                         

    Operational state             : up                                         

    Serial number                 :     109917C1204W513                        

    Firmware revision             : HDX 2.1                                    

    Model number                  : SanDisk SDCFBI-128                         

    Size                          : 125,038 KB                                 

    Free space                    : 116,238 KB                                 

Hardware Data

    Part number                   : 3HE00316AAAA01                             

    CLEI code                     : IPUCACMFAA                                 

    Serial number                 : NS043610538                                

    Manufacture date              : 02252005                                   

    Manufacturing string          :                                            

    Manufacturing deviations      :                                            

    Administrative state          : up                                         

    Operational state             : up                                         

    Temperature                   : 43C                                        

    Temperature threshold         : 75C                                        

    Software boot version         : X-2.0.R12 on Mon Jan 24 12:03:16 PST 2007 *

    Software version              : TiMOS-C-4.0.private cpm/hops ALCATEL SR 77*

    Time of last boot             : 2007/04/11 09:39:23                        

    Current alarm state           : alarm cleared                              

    Base MAC address              : 00:03:fa:30:7c:3c                          

    Memory capacity               : 2,016 MB                                   

===============================================================================

B:Dut-D# 

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
Billion BiPAC 4500NZ(L) User Manual preview
BiPAC 4500NZ(L)
Brand: Billion Pages: 146
A-Link WNAP4G Quick Installaion Manual preview
WNAP4G
Brand: A-Link Pages: 6
ZyXEL Communications XS1920 Series User Manual preview
XS1920 Series
Brand: ZyXEL Communications Pages: 422
XtendLan NVR-xUD User Manual preview
NVR-xUD
Brand: XtendLan Pages: 228
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
ZyXEL Communications P-335U Specifications preview
P-335U
Brand: ZyXEL Communications Pages: 2
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
JLCooper Electronics GangWay32 User Manual preview
GangWay32
Brand: JLCooper Electronics Pages: 12
CyberPower CyberPower RMCARD201 Quick Install Manual preview
CyberPower RMCARD201
Brand: CyberPower Pages: 8
Netopia D3100-I User Reference Manual preview
D3100-I
Brand: Netopia Pages: 138
Tripp Lite N201-100-GY-P Specification Sheet preview
N201-100-GY-P
Brand: Tripp Lite Pages: 2
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25
IEI Technology PUZZLE-5030 User Manual preview
PUZZLE-5030
Brand: IEI Technology Pages: 119
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
Zte MF971R Quick Start Manual preview
MF971R
Brand: Zte Pages: 28
Billion BiPAC 7820NZ User Manual preview
BiPAC 7820NZ
Brand: Billion Pages: 100

Brands by name

Popular brands

Load more brands