Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 253 | Manualshive

Page: 253 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 253

framing

Syntax

framing

{

sonet

|

sdh

}

Context

config>port>sonet-sdh

Description

This command specifies SONET/SDH framing to be either SONET or SDH.

Default

sonet

Parameters

sonet —

Configures the port for SONET framing.

sdh —

Configures the port for SDH framing.

group

Syntax

group

sonet-sdh-index

payload

{

tu3

|

vt2

|

vt15

}

Context

config>port>sonet-sdh

Description

This command configures payload of the SONET/SDH group.

For example:

config>port>sonet-sdh#

group tug3-1.1 payload tu3
group tug3-1.2 payload vt2
group tug3-1.3 payload vt2
group tug3-2.1 payload vt15
group tug3-2.2 payload vt15
group tug3-2.3 payload tu3
group tug3-3.1 payload tu3
group tug3-3.2 payload tu3
group tug3-3.3 payload tu3

Default

none

Parameters

sonet-sdh-index —

Specifies the components making up the specified SONET/SDH path. Depending

on the type of SONET/SDH port the

sonet-sdh-index

must specify more path indexes to specify

the payload location of the path.

tu3 —

Specify the Tributary Unit Group (TUG3) on a path. Configures the port or channel for

transport network use.

vt2 —

Configures the path as a virtual tributary group of type vt2.

vt15 —

Configures the path as a virtual tributary group of type vt15.

«
...
251
252
253
254
255
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Storagelibrary T24

Brand: Tandberg Data Pages: 28

Brand: Patton electronics Pages: 12

Brand: HARTING Pages: 13

Brand: ICP DAS USA Pages: 8

ConnectX-3 Pro MCX349A-XCCN

Brand: Mellanox Technologies Pages: 35

Brand: Buffalo Pages: 2

SmartSwitch 8-slot

Brand: Cabletron Systems Pages: 150

VAR-SOM-MX8M-PLUS

Brand: Variscite Pages: 2

LinkStation 500

Brand: Buffalo Pages: 139

ipRocketLink 3101 Series

Brand: Patton Pages: 119

Brand: Valcom Pages: 3

OfficeConnect 3CXSH654B

Brand: 3Com Pages: 52

Brand: CTC Union Pages: 12

Brand: Proxim Pages: 65

Brand: Intercel Pages: 17

Brand: Ultra Pages: 4

DynaStar DS2000-IFR

Brand: GarrettCom Pages: 40

Brand: Foscam Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands