Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 415

Page: 415 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 415

pvp

Syntax

pvp

[

vpi

] [

detail

]

Context

show>multilink-bundle>ima>atm

Description

This command displays ATM port PVP information.

Parameters

vpi —

Displays the VPI values.

Values

vpi: 0 — 4095 (NNI)

0 — 255 (UNI)

detail —

Provides detailed information.

MDA Values

1, 2

Output

Show Mutlilink-bundle IMA ATM PVP Output —

The following table describes show

multilink-bundle IMA ATM port-connection output fields.

Sample Output

A:ima2# show multilink-bundle bundle-ima-1/1.1 ima atm pvp

================================================================

ATM PVPs, Port bundle-ima-1/1.1

================================================================

VPI Owner Type Ing.TD Egr.TD Adm OAM Opr

----------------------------------------------------------------

2 SAP PVP 1 1 up up up

================================================================

Label

Description

VPI

Displays the VPI value.

Owner

Identifies the system entity that owns a specific ATM connection.

Type

Specifies the type of this multilink bundle.

mlppp —

Indicates that the bundle is of type MLPPP.

ima —

Indicates that the bundle is of type IMA group.

Ing.TD

Specifies the ATM traffic descriptor profile that applies to the receive
direction of the interface connection.

Eng.TD

Specifies the ATM traffic descriptor profile that applies to the transmit
direction of the interface connection.

Adm

ima —

Indicates that the bundle is of type IMA group.

Down —

The bundle is administratively down.

OAM

Indicates the OAM operational status of ATM connections.

Opr

Up —

The bundle is operationally up.

Down —

The bundle is operationally down.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands