Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 23 | Manualshive

Page: 23 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 23

Channelized MDA Support

DS-3/E-3

Each 4-port or 12-port channelized DS-3/E-3 media dependent adapter (MDA) supports
channelization down to digital signal level 0 (DS-0) using a maximum of 8 or 24 (respectively)
1.0/2.3 coaxial connectors. Each port consists of one receive (RX) coaxial connector and one
transmit (TX) coaxial connector.

Each physical DS-3 connection can support a full clear-channel DS-3, or it can be channelized
into independent DS-1/E-1 data channels. Each DS1/E1 channel can then be further channelized
down to DS-0s. E-3 ports do not support channelization. They only support clear channel
operation.

Each DS-3/E-3 MDA supports 512 channels with DS-0 timeslots that are used in the DS-1/E-1
channel-group.

Channelized OC-12/STM-4

Each 1-port channelized OC-12/STM-4 MDA supports channelization down to DS-0 and accepts
one OC-12/STM-4 SFP small form factor pluggable (SFP) module. The same SFP optics used on
Alcatel-Lucent’s SONET/SDH cards can be used on the channelized OC-12/STM-4 MDA.

Each channelized OC-12/STM-4 supports 512 channels with DS-0 timeslots that are used in the
DS-1/E-1 channel-group. DS-3 TDM channels can be further channelized to DS-1/E-1 channel
groups. An E3 TDM channel cannot be channelized and can only be configured in clear channel
operation.

Channelized CHOC-3/STM-1

Each 1-port channelized OC-3/STM-1 MDA supports channelization down to DS-0 and accepts
one OC-3/STM-1 SFP small form factor pluggable (SFP) module. The same SFP optics used on
Alcatel-Lucent’s SONET/SDH cards can be used on the channelized OC-3/STM-1 MDA.

Each channelized OC-3/STM-1 supports 512 channels with DS-0 timeslots that are used in the
DS-1 channel-group. DS-3 TDM channels can be further channelized to DS-1/E-1 channel groups.
An E3 TDM channel cannot be channelized and can only be configured in clear channel operation.

«
...
21
22
23
24
25
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: Paradyne Pages: 86

Express Ethernetwork DI-704P

Brand: D-Link Pages: 2

Brand: Dahua Pages: 24

AT-9424Ts/XP AC

Brand: Allied Telesis Pages: 3

LoadMaster 1500

Brand: KEMP Technologies Pages: 71

Brand: Aztech Pages: 2

Brand: Kontron Pages: 42

SmartNode 4520 Series

Brand: Patton electronics Pages: 90

3C8567 - SuperStack II NETBuilder SI 567...

Brand: 3Com Pages: 6

Brand: Global Sun Pages: 39

Ether-GSH24T v3

Brand: AirLive Pages: 2

Brand: Intellinet Pages: 32

Brand: M86 Security Pages: 512

WNR2000v2 - Wireless- N 300 Router

Brand: NETGEAR Pages: 144

BladeCenter 1/10 Gb Uplink Ethernet SwitchModule

Brand: IBM Pages: 58

Brand: NETGEAR Pages: 2

Campus BridgeLINK

Brand: RadioLAN Pages: 146

HDMI Input Card DMC-HD

Brand: Crestron Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands