manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Show Commands

Page 366

7750 SR OS Interface Configuration Guide

ALA-12# show port 7/1/1.1.1

===============================================================================

TDM DS0 Chan Group

===============================================================================

Description        : DS0GRP

Interface          : 3/1/1.1.1

TimeSlots          : 1

Speed              : 64                      CRC                  : 16

Admin Status       : up                      Oper status          : down

Last State Change  : 04/11/2007 06:54:28     Chan-Grp IfIndex     : 589332542

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1518                    Oper MTU             : 1518

Physical Link      : No                      Bundle Number        : none

Idle Cycle Flags   : flags                   Load-balance-algo    : default

===============================================================================

Traffic Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Octets                                                 0                      0

Packets                                                0                      0

Errors                                                 0                      0

===============================================================================

Port Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Packets                                                0                      0

Discards                                               0                      0

Unknown Proto Discards                                 0

===============================================================================

ALA-12#

A:ALA-48# show port 3/1/3.e3

===============================================================================

TDM Interface

===============================================================================

Description        : E3

Interface          : 3/1/3.e3

Type               : e3                      Framing              : g751

Admin Status       : up                      Oper status          : down

Physical Link      : No                      Clock Source         : loop-timed

Last State Change  : 04/11/2007 06:54:28     Port IfIndex         : 589398019

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1518                    Oper MTU             : 1518

CRC                : 16                      Channelized          : none

Idle Cycle Flags   : flags                   Loopback             : none

FEAC Loop Respond  : Disabled                In FEAC Loop         : No

BERT Pattern       : none                    BERT Duration        : N/A

Err Insertion Rate : 0                       Last BERT Synched    : 0 Seconds

BERT Status        : idle                    Last BERT Errors     : 0

                                             Last BERT Total Bits : 0

Cfg Alarm          : ais los

Alarm Status       :

Subrate Mode       : none

MDL Transmit       : none

-------------------------------------------------------------------------------

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Canon Vb-C60 - Ptz Network Camera Setup Manual preview
Vb-C60 - Ptz Network Camera
Brand: Canon Pages: 30
Panasonic KX-UDS124 Maintenance Tool Manual preview
KX-UDS124
Brand: Panasonic Pages: 24
Panasonic i-Pro WV-SP302 Speci?Cations preview
i-Pro WV-SP302
Brand: Panasonic Pages: 2
Panasonic BB-HCM381A - Network Camera Troubleshooting Manual preview
BB-HCM381A - Network Camera
Brand: Panasonic Pages: 28
Panasonic BB-HCM381A - Network Camera Installation Manual preview
BB-HCM381A - Network Camera
Brand: Panasonic Pages: 2
LAWO edge User Manual preview
edge
Brand: LAWO Pages: 154
N-Tron 7018 User Manual & Installation Manual preview
7018
Brand: N-Tron Pages: 138
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Watchguard Firebox T20-W Quick Start Manual preview
Firebox T20-W
Brand: Watchguard Pages: 40
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
XYZ Machine Tools TRAK 2OP M11 Mill Safety, Installation, Maintenance, Service And Parts List preview
TRAK 2OP M11 Mill
Brand: XYZ Machine Tools Pages: 203
Ravpower RD-WD009 User Manual preview
RD-WD009
Brand: Ravpower Pages: 27
Z Microsystems TranzStor 8X User Manual preview
TranzStor 8X
Brand: Z Microsystems Pages: 51
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
TP-Link TD-8816 Quick Installation Manual preview
TD-8816
Brand: TP-Link Pages: 2
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
eWON 2101CD Installation Manual preview
2101CD
Brand: eWON Pages: 34
ANTAIRA LMP-1202G-SFP Series Hardware Manual preview
LMP-1202G-SFP Series
Brand: ANTAIRA Pages: 19

Brands by name

Popular brands

Load more brands