Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 120 | Manualshive

Page: 120 / 444

background image

Configuring Ports

Page 120

7750 SR OS Interface Configuration Guide

Note:

The E1 encapsulation in the ASAP MDA and in the channelized MDAs is compliant to

G.704 and G.703. The G.703 feature allows a user to configure an unstructured E1 channel on
deep channel MDAs and ASAP MDAs. In G.704, time slot 0 is used to carry timing information
by a service provider and thus, only 31 slots are available to the end user. In G.703, all 32 time
slots are available to the end user. Timing is provided by the end user.

SDH

STM4>AUG4>AUG1>VC4>TUG3>TUG2>TU12
>VC11

None

SDH

STM4>AUG4>AUG1>VC3>TUG2>VC11

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SDH

STM4>AUG4>AUG1>VC4>TUG3>TUG2>VC12

m1-choc12
m4-choc3
m12-chds3

SDH

STM4>AUG4>AUG1>VC3>TUG2>VC12

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SDH

STM4>AUG4>AUG1>VC4>TUG3>VC3>DS3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SDH

STM4>AUG4>AUG1>VC3>DS3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SONET

OC12>STS12>STS1 SPE>VT GROUP>VT1.5 SPE

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

SONET

OC12>STS12>STS1 SPE>VT GROUP>VT2 SPE

m1-choc12
m4-choc3
m12-chds3

SONET

OC12>STS12>STS1 SPE>DS3

m1-choc12
m4-choc3
m12-chds3
m4-choc3-as

Table 20: Channelization Options Available on the 7750 SR Channelized MDAs (Continued)

Framing

Channelization/mapping option

Channelized MDAs Supporting

Services on the Port/Channel

«
...
118
119
120
121
122
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

Brand: Oracle Pages: 112

Brand: Net to Net Technologies Pages: 4

Brand: ZyXEL Communications Pages: 299

Brand: SyChip Pages: 24

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Brand: Belden Pages: 84

Brand: TP-Link Pages: 131

Brand: Razer Pages: 17

Brand: Topcom Pages: 16

Brand: DPS Pages: 57

IP Board IPT10000C

Brand: Dialogic Pages: 2

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 17

Brand: LaView Pages: 2

Dynalink MyZone 3G24W

Brand: NetComm Pages: 5

Brand: Teltonika Pages: 12

3C13755-US - Router 5642

Brand: 3Com Pages: 104

Brand: NetApp Pages: 10

Brand: ADTRAN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands