manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 76 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 76

Port Features

Page 76

7750 SR OS Interface Configuration Guide

→

If multiple groups satisfy the selection criteria, the sub-group being currently active 
remains active. Initially, the sub-group containing the highest priority eligible link is 
selected.

→

Only links pertaining to a single sub-group are active at any time.

→

An eligible member refers to a LAG member link which can potentially become 
active. This means it is operationally up, and if the slave-to-partner flag is set, the 
remote system did not disable its use (by signalling stand-by).

•

The selection algorithm works in a reverting mode. This means that every time the 
configuration or status of any link in a LAG changes, the selection algorithm is re-run. In 
case of a tie between two groups (one of them being currently active) the active group 
remains active (no reverting).

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments