Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 27

Page: 27 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 27

Supported real-time DDM features are summarized in

Table 3

Table 3:

Real-Time DDM Information

Parameter

User Units

SFP/XFP

Units

SFP

XFP

Temperature

Celsius

Supported

Supply
Voltage

Volts

µV

Supported

TX Bias
Current

µA

Supported

TX Output
Power

dBm (converted from
mW)

Supported

RX Received
Optical
Power4

dBm (converted from
dBm) (Avg Rx Power or
OMA)

Supported

AUX1

parameter dependent
(embedded in transceiver)

Not supported

Supported

AUX2

parameter dependent
(embedded in transceiver)

Not supported

Supported

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 27 / 444

Search results

Summary of Contents for 7750 SR OS

Reviews: