Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 440

Page: 440 / 444

Standards and Protocols

Page 440

Standards and Protocols

FRF2.2

-PVC Network-to- Network

Interface (NNI) Implementation
Agreement.

ITU-T Q.933 Annex A-

IPSec

RFC 2401 Security Architecture for the

Internet Protocol

RFC 3706 IKE Dead Peer Detection
RFC 3947 Negotiation of NAT-Traversal

in the IKE

RFC 3948 UDP Encapsulation of IPsec

ESP Packets

IS-IS

RFC 1142 OSI IS-IS Intra-domain

Routing Protocol (ISO 10589)

RFC 1195 Use of OSI IS-IS for routing in

TCP/IP & dual environments

RFC 2763 Dynamic Hostname Exchange

for IS-IS

RFC 2966 Domain-wide Prefix

Distribution with Two-Level IS-IS

RFC 2973 IS-IS Mesh Groups
RFC 3373 Three-Way Handshake for

Intermediate System to Intermediate
System (IS-IS) Point-to-Point
Adjacencies

RFC 3567 Intermediate System to

Intermediate System (ISIS)
Cryptographic Authentication

RFC 3719 Recommendations for

Interoperable Networks using IS-IS

RFC 3784 Intermediate System to

Intermediate System (IS-IS)
Extensions for Traffic Engineering
(TE)

RFC 3787 Recommendations for

Interoperable IP Networks

RFC 3847 Restart Signaling for IS-IS ñ

GR helper

RFC 4205 for Shared Risk Link Group

(SRLG) TLV

draft-ietf-isis-igp-p2p-over-lan-05.txt
draft-ietf-isis-wg-mib-05.txt

IPv6

RFC 1981 Path MTU Discovery for IPv6
RFC 2375 IPv6 Multicast Address

Assignments

RFC 2460 Internet Protocol, Version 6

(IPv6) Specification

RFC 2461 Neighbor Discovery for IPv6
RFC 2462 IPv6 Stateless Address Auto

configuration

RFC 2463 Internet Control Message

Protocol (ICMPv6) for the Internet
Protocol Version 6 Specification

RFC 2464 Transmission of IPv6 Packets

over Ethernet Networks

RFC 2529 Transmission of IPv6 over

IPv4 Domains without Explicit
Tunnels

RFC 2545 Use of BGP-4 Multiprotocol

Extension for IPv6 Inter-Domain
Routing

RFC 2710 Multicast Listener Discovery

(MLD) for IPv6

RFC 2740 OSPF for IPv6
RFC 3306 Unicast-Prefix-based IPv6

Multicast Addresses

RFC 3315 Dynamic Host Configuration

Protocol for IPv6

RFC 3587 IPv6 Global Unicast Address

Format

RFC3590 Source Address Selection for

the Multicast Listener Discovery
(MLD) Protocol

RFC 3810 Multicast Listener Discovery

Version 2 (MLDv2) for IPv6

RFC 4007 IPv6 Scoped Address

Architecture

RFC 4193 Unique Local IPv6 Unicast

Addresses

RFC 4291 IPv6 Addressing Architecture
RFC 4659 BGP-MPLS IP Virtual Private

Network (VPN) Extension for IPv6
VPN

RFC 5072 IP Version 6 over PPP
draft-ietf-isis-ipv6-05
draft-ietf-isis-wg-multi-topology-xx.txt

LDP

RFC 3036 LDP Specification
RFC 3037 LDP Applicability
RFC 3478 Graceful Restart Mechanism

for LDP - GR helper

draft-jork-ldp-igp-sync-03

MPLS

RFC 3031 MPLS Architecture
RFC 3032 MPLS Label Stack
Encoding (REV3443))
RFC 4379 Detecting Multi-Protocol

Label Switched (MPLS) Data Plane
Failures

RFC 4182 Removing a Restriction on
the use of MPLS Explicit NULL
draft-ietf-mpls-lsr-mib-06.txt

draft-ietf-mpls-te-mib-04.txt
draft-ietf-mpls-ldp-mib-07.txt

Multicast

RFC 1112 Host Extensions for IP

Multicasting (Snooping)

RFC 2236 Internet Group Management

Protocol, (Snooping)

RFC 3376 Internet Group Management

Protocol, Version 3 (Snooping)

RFC 2362 Protocol Independent

Multicast-Sparse Mode (PIMSM)

RFC 3618 Multicast Source Discovery

Protocol (MSDP)

RFC 3446 Anycast Rendezvous Point

(RP) mechanism using Protocol
Independent Multicast (PIM) and
Multicast Source Discovery
Protocol (MSDP)

RFC 4601 Protocol Independent

Multicast - Sparse Mode (PIM-SM):
Protocol Specification (Revised)

RFC 4604 Using IGMPv3 and MLDv2

for Source-Specific Multicast

RFC 4607 Source-Specific Multicast for

RFC 4608 Source-Specific Protocol

Independent Multicast in 232/8

RFC 4610 Anycast-RP Using Protocol

Independent Multicast (PIM)

draft-ietf-pim-sm-bsr-06.txt
draft-rosen-vpn-mcast-08.txt
draft-ietf-mboned-msdp-mib-01.txt

NETWORK MANAGEMENT

ITU-T X.721: Information technology-

OSI-Structure of Management
Information

ITU-T X.734: Information technology-

OSI-Systems Management: Event
Report Management Function

M.3100/3120 Equipment and Connection

Models

TMF 509/613 Network Connectivity

Model

RFC 1157 SNMPv1
RFC 1215 A Convention for Defining

Traps for use with the SNMP

RFC 1657 BGP4-MIB
RFC 1724 RIPv2-MIB
RFC 1850 OSPF-MIB
RFC 1907 SNMPv2-MIB
RFC 2011 IP-MIB
RFC 2012 TCP-MIB

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands