manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 394 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 394

Show Commands

Page 394

7750 SR OS Interface Configuration Guide

Sync Tag       : ring11

Port ID        : 1/1/3

Admin State    : inService

Oper State     : connected

Admin Change   : 01/07/2008 21:40:07

Oper Change    : 01/07/2008 21:40:24

Last Debounce  : 02/15/2008 09:28:42

Debounce Period: 0d 00:00:00

Failure Reason : None

------------------------------------------------------------------------------

In Band Control Path

------------------------------------------------------------------------------

Service ID     : 10

Interface Name : to_an1

Oper State     : connected

Dest IP        : 10.10.0.2

Src  IP        : 10.10.0.1

------------------------------------------------------------------------------

VLAN Map B Path Provisioned

------------------------------------------------------------------------------

range 13-13

range 17-17

------------------------------------------------------------------------------

VLAN Map Excluded Path Provisioned

------------------------------------------------------------------------------

range 18-18

------------------------------------------------------------------------------

VLAN Map B Path Operational

------------------------------------------------------------------------------

range 13-13

range 17-17

------------------------------------------------------------------------------

VLAN Map Excluded Path Operational

------------------------------------------------------------------------------

range 18-18

==============================================================================

*A:ALA-48# 

*A:ALA-48>show>redundancy>multi-chassis# mc-ring peer 192.251.10.104

==============================================================================

MC Ring entries

==============================================================================

Sync Tag                         Oper State      Failure Reason

------------------------------------------------------------------------------

No. of MC Ring entries: 0

==============================================================================

*A:ALA-48# 

*A:ALA-48# show redundancy multi-chassis mc-ring peer 10.0.0.2

=============================================================================

MC Ring entries

==============================================================================

Sync Tag                         Oper State      Failure Reason

------------------------------------------------------------------------------

ring11                           connected       None

ring12                           shutdown        None

------------------------------------------------------------------------------

No. of MC Ring entries: 4

==============================================================================

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments