manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Show Commands

Page 404

7750 SR OS Interface Configuration Guide

A:timetra-sim110# show multilink-bundle bundle-ppp-1/1.1 detail 

===============================================================================

Bundle bundle-ppp-1/1.1 Detail

===============================================================================

Description        : MultiLink Bundle

Bundle Id          : bundle-ppp-1/1.1   Type               : mlppp             

Admin Status       : down               Oper Status        : down              

Minimum Links      : 1                  Bundle IfIndex     : 555745281         

Total Links        : 0                  Active Links       : 0                 

Red Diff Delay     : 0                  Yellow Diff Delay  : 0                 

Red Diff Delay Act : none               MRRU               : 1524              

Short Sequence     : false              Oper MRRU          : 1524              

Oper MTU           : 1522               Fragment Threshold : 128 bytes         

Up Time            : N/A                Bandwidth          : 0 KBit            

PPP Input Discards : 0                  Primary Member Port: None              

Interleave-Frag    : false 

===============================================================================

Traffic Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Octets                                                 0                      0

Packets                                                0                      0

Errors                                                 0                      0

===============================================================================

Port Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Unicast Packets                                        0                      0

Multicast Packets                                      0                      0

Broadcast Packets                                      0                      0

Discards                                               0                      0

Unknown Proto Discards                                 0                       

===============================================================================

A:timetra-sim110#

relations

Syntax

relations

Context

show>multilink-bundle

Description

This command displays the working and protection bundles associated with this bundle-id.

Output

Show Mutlilink-Bundle Relations Output — 

The following table describes show multilink-

bundle relations output fields. 

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

D-Link DES-3526 - Switch - Stackable Manual preview
DES-3526 - Switch - Stackable
Brand: D-Link Pages: 258
Abocom FW200 Specifications preview
FW200
Brand: Abocom Pages: 1
Yamaha mLAN Driver Manual Book preview
mLAN Driver
Brand: Yamaha Pages: 24
Yamaha DSP1D Supplementary Manual preview
DSP1D
Brand: Yamaha Pages: 5
H3C S12500R-2L Installation, Quick Start preview
S12500R-2L
Brand: H3C Pages: 26
EVOC 6336-STG-YX Manual preview
6336-STG-YX
Brand: EVOC Pages: 57
IMC Networks iMcV-FiberLinX Operation Manual preview
iMcV-FiberLinX
Brand: IMC Networks Pages: 36
LevelOne FSW-0808TX Quick Start Manual preview
FSW-0808TX
Brand: LevelOne Pages: 3
Unex EVK-351 Quick Start Manual preview
EVK-351
Brand: Unex Pages: 27
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12
8e6 Technologies HL-002-006 Quick Start Manual preview
HL-002-006
Brand: 8e6 Technologies Pages: 94
SMC Networks Barricade SMC7908VoWBRA2 Specifications preview
Barricade SMC7908VoWBRA2
Brand: SMC Networks Pages: 2
Dahua DHI-NVR5208-4KS2 User Manual preview
DHI-NVR5208-4KS2
Brand: Dahua Pages: 361
Dahua NVR5208-EI User Manual preview
NVR5208-EI
Brand: Dahua Pages: 489
MSE PSE-608R User Manual preview
PSE-608R
Brand: MSE Pages: 35
Huawei WiFi Q2 Quick Start Manual preview
WiFi Q2
Brand: Huawei Pages: 52
Huawei WiFi AX3 Quick Start Manual preview
WiFi AX3
Brand: Huawei Pages: 389
Huawei WiFi Cube 2 4G Quick Start Manual preview
WiFi Cube 2 4G
Brand: Huawei Pages: 24

Brands by name

Popular brands

Load more brands