manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 285

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 285

config>port>tdm>e1
config>port>tdm>e1>channel-group
config>port>tdm>e3

Description

This command configures the value that the HDLC TDM DS-0, E-1, E-3, DS-1, or DS-3 interface 
transmits during idle cycles. For ATM ports/channels/channel-groups, the configuration does not 
apply and only the no form is accepted.

The 

no

 form of this command reverts the idle cycle flag to the default value.

Default

flags (0x7E)

no flags (ATM)

Parameters

flags — 

Specifies that 0x7E is used as the idle cycle flag.

ones  — 

Specifies that 0xFF is used as the idle cycle flag.

idle-payload-fill

Syntax

idle-payload-fill

 {

all-ones

}

idle-payload-fill pattern

 pattern

no idle-payload-fill

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the data pattern to be transmitted when the circuit emulation service is not 
operational or temporarily experiences under-run conditions.  This command is only valid for cesopsn 
and cesopsn-cas circuit emulation services. It is blocked with a warning for unstructured (satop) 
circuit emulation services.

Default

all-ones

Parameters

all-ones — 

Defines the 8 bit value to be transmitted as 11111111.

pattern — 

Transmits a user-defined pattern.

idle-signal-fill

Syntax

idle-signal-fill 

{

all-ones

}

idle-signal-fill pattern 

pattern

no idle-signal-fill

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the signaling pattern to be transmitted when the circuit emulation service is 
not operational or temporarily experiences under-run conditions.  This command is only valid for 
cesopsn-cas circuit emulation services. It is blocked with a warning for unstructured (satop) and basic 
cesopsn circuit emulation services.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands