Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 259

Page: 259 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 259

Default

none

Parameters

sts3 —

Configures STS3/STM1 payload as clear channel.

tu3 —

Configures STS3/STM1 payload as Tributary Unit Group 3 (TUG3).

ds3 —

Configures the port or channel as DS-3 STS1/VC3 payload as DS-3.

e3 —

Configures the port or channel as E-3 STS1/VC3 payload as E-3.

vt2 —

Configures the path STS1 payload as vt2 as a virtual tributary group. Only allowed on STS-1

nodes. (SONET VT container)

vt15 —

Configures the path as a virtual tributary group. Only allowed on STS-1 nodes. (SONET VT

container)

ds1 —

Configures the port or channel as DS1.vt15 or vt2 payload as DS-1

e1 —

Configures VT2 payload as E-1.

report-alarm

Syntax

[

]

report-alarms

[

pais

] [

plop

] [

prdi

] [

pplm

] [

prei

] [

puneq

] [

plcd

]

Context

config>port>sonet-sdh>path

Description

This command enables logging of SONET (SDH) path alarms for a SONET-SDH port. Only path
alarms can be configured in the channel context.

The

form of this command disables logging of the specified alarms.

Parameters

pais —

Reports path alarm indication signal errors. When configured,

pais

alarms are raised and

cleared.

Default

pais

alarms are not issued

plop —

Reports path loss of pointer (per tributary) errors. When configured,

plop

traps are raised but

not cleared.

Default

plop

traps are issued

prdi —

Reports path remote defect indication errors. When configured,

prdi

alarms are raised and

cleared.

Default

prdi

alarms are not issued

pplm —

Reports a path payload mismatch, as a result the channel will be operationally downed.

When configured,

pplm

traps are raised but not cleared.

Default

pplm

traps are issued

prei —

Reports a path error condition raised by the remote as a result of b3 errors received from this

node. When configured,

prei

traps are raised but not cleared.

Default

prei

traps are not issued

puneq —

Reports path unequipped errors. Reports path unequipped signal errors.

Default

puneq traps are issued

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands