Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 291 | Manualshive

Page: 291 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 291

The

no

form of this command reverts to the default value.

Default

threshold ber-sd rate 5
threshold ber-sf rate 50

Parameters

ber-sd —

Specifies the BER that specifies signal degradation.

ber-sf —

Specifies the BER that specifies signal failure.

rate —

Specifies the number of errors, in millions.

timeslots

Syntax

timeslots

timeslots

no timeslots

Context

config>port>tdm>ds1>channel-group
config>port>tdm>e1>channel-group

Description

This command defines the list of DS-0 timeslots to be used in the DS-1/E-1 channel-group. The
timeslots are defaulted as defined below when encap-type is set to/from atm. ATM channel groups do
not allow timeslots to change.

The

no

form of this command removes DS-0 timeslots from a channel group.

Default

no timeslots — Non-ATM channel groups.
1-24 — Channel groups configured under DS-1 with encap set to ATM.
2-16,18-32 — Channel groups configured under E-1 with encap set to ATM.

Parameters

timeslots —

Specifies the timeslot(s) to be associated with the channel group. The value can consist

of a list of timeslots. Each member of the list can either be a single timeslot or a range of
timeslots.

Values

1 — 24 for DS-1 interfaces (the full range is auto-configured for ATM channel
groups and cannot be changed).
2 — 32 for E-1 interfaces (the 2 — 16,18 — 32 ranges are auto-configured for
ATM channel groups and cannot be changed).

«
...
289
290
291
292
293
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: Aastra Pages: 2

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brand: H3C Pages: 8

Brand: H3C Pages: 9

Brand: H3C Pages: 33

Brand: H3C Pages: 42

Brand: H3C Pages: 102

S12500CR Series

Brand: H3C Pages: 9

Brand: H3C Pages: 15

H3C S7500E Series

Brand: H3C Pages: 1565

Brand: H3C Pages: 4

Brand: Javad Pages: 35

Brand: Lorex Pages: 186

Brand: DPtech Pages: 39

Brand: KPN Pages: 14

MasterBus Tanklevel Interface

Brand: Mastervolt Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands