manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 365 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 365

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 365

Sample Output

A:ALA-7# show port 7/1/1.ds0grp-1.1

================================================================================

TDM DS0 Chan Group

================================================================================

Description        : DS3

Interface          : 7/1/1.ds0grp-1.1

TimeSlots          : 1

Speed              : 64                      CRC                  : 16

Admin Status       : up                      Oper status          : down

Last State Change  : 2007/04/11 01:14:37     Chan-Grp IfIndex     : 656441433

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1522                    Oper MTU             : 1522

Physical Link      : No

================================================================================

Port Statistics

=======================================================================

                                         Input                  Output

-----------------------------------------------------------------------

Unicast Packets                              0                       0

Multicast Packets                            0                       0

Broadcast Packets                            0                       0

Discards                                     0                       0

Unknown Proto Discards                       0

=======================================================================

A:ALA-7#

A:ALA-7# show port 7/1/1.ds0grp-1.1 detail

================================================================================

TDM DS0 Chan Group

================================================================================

Description        : DS3

Interface          : 7/1/1.ds0grp-1.1

TimeSlots          : 1

Speed              : 64                      CRC                  : 16

Admin Status       : up                      Oper status          : down

Last State Change  : 04/11/2007 01:14:37     Chan-Grp IfIndex     : 656441433

Configured mode    : access                  Encap Type           : bcp-null

Admin MTU          : 1522                    Oper MTU             : 1522

Physical Link      : No

================================================================================

Port Statistics

=======================================================================

                                         Input                  Output

-----------------------------------------------------------------------

Unicast Packets                              0                       0

Multicast Packets                            0                       0

Broadcast Packets                            0                       0

Discards                                     0                       0

Unknown Proto Discards                       0

=======================================================================

A:ALA-7#

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments