manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

The Alcatel-Lucent 7750 SR OS is a high-performing networking product used by professionals worldwide. Enhance your understanding of its powerful features and gain expertise in interface configuration with the comprehensive interface configuration manual, available for free download. Visit our website to get your hands on this invaluable resource.

Share
Download
background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 373

Sample Output

A:ALA-2934 show mda 7/2 detail (ATM MDA)

========================================================================== 

MDA 7/2 detail 

========================================================================== 

Slot Mda  Provisioned          Equipped             Admin    Operational 

          Mda-type             Mda-type             State    State 

-------------------------------------------------------------------------- 

7    2    m4-atmoc12/3-sfp     m4-atmoc12/3-sfp     up       up 

MDA Specific Data 

    Maximum port count            : 4 

    Number of ports equipped      : 4 

    Transmit timing selected      : CPM Card B 

    Sync interface timing status  : Qualified 

    Network ingress queue policy  : default 

    Capabilities                  : Sonet, ATM 

    Min channel size              : Sonet STS-12 

    Max channel size              : Sonet STS-12 

    Max number of channels        : 4 

    Channels in use               : 0 

Egress RT-VBR

Indicates the total real-time variable bit rate (rt-VBR) bandwidth con-
sumed on this interface in the egress direction.

Ingress NRT-VBR

Indicates the total non-real-time variable bit rate (nrt-VBR) bandwidth 
consumed on this interface in the ingress direction.

Egress NRT-VBR

Indicates the total non-real-time variable bit rate (nrt-VBR) bandwidth 
consumed on this interface in the egress direction.

Ingress UBR

Indicates the total unspecified bit rate (UBR) bandwidth consumed on 
this interface in the ingress direction.

Egress UBR

Indicates the total unspecified bit rate (UBR) bandwidth consumed on 
this interface in the egress direction.

Ingress Total

Indicates the number of valid ATM cells received by the ATM interface 
including both CLP=0 and CLP=1 cells. If traffic policing is imple-
mented, then cells are counted prior to the application of traffic polic-
ing.

ATM Link Band-

width

Indicates the total ATM link bandwidth accepted on this interface.

Shaped Bandwidth

Indicates the total shaped bandwidth consumed on this interface in the 
egress direction.

HEC Errors 

(Dropped)

Indicates the number of cells with uncorrectable HEC errors on this 
interface.

HEC Errors 

(Fixed)

Label

Description  (Continued)

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Lantronix Maestro E220 Series Quick Start Manual preview
Maestro E220 Series
Brand: Lantronix Pages: 25
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Queclink GV600 Series Instruction Manual preview
GV600 Series
Brand: Queclink Pages: 9
Sangamo CHOICE PR1 User Instructions preview
CHOICE PR1
Brand: Sangamo Pages: 2
H3C CR1606-F Installation Instructions Manual preview
CR1606-F
Brand: H3C Pages: 12
Patton electronics 3087 Quick Start Manual preview
3087
Brand: Patton electronics Pages: 12
Netis DL4305 Quick Installation Manual preview
DL4305
Brand: Netis Pages: 16
Tripp Lite N201-001-BL Specification Sheet preview
N201-001-BL
Brand: Tripp Lite Pages: 3
Alphatech Blue Gate ISDN BRI Brave Quick Start Manual preview
Blue Gate ISDN BRI Brave
Brand: Alphatech Pages: 6
Airlink101 AR725W User Manual preview
AR725W
Brand: Airlink101 Pages: 64
ETAS ES1337.2 User Manual preview
ES1337.2
Brand: ETAS Pages: 29
3Com NETBuilder SI Using Manual preview
NETBuilder SI
Brand: 3Com Pages: 212
Multiplex MULTIflight Stick Operating Instructions Manual preview
MULTIflight Stick
Brand: Multiplex Pages: 10
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Brand: ZyXEL Communications Pages: 114
netsys NH-310S User Manual preview
NH-310S
Brand: netsys Pages: 38
IC Realtime nvr700ns User Manual preview
nvr700ns
Brand: IC Realtime Pages: 131

Brands by name

Popular brands

Load more brands