Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 157 | Manualshive

Page: 157 / 444

background image

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 157

Modifying a Card Type

In order to modify the card type already provisioned for a specific slot, you must shutdown
existing port configurations and shutdown and remove all MDA configurations.

Use the following CLI syntax to modify a card type already provisioned for a specific slot:

CLI Syntax:

config> port

port-id

[no] shutdown

CLI Syntax:

config> card

slot-number

mda mda-number

[no] mda-type

mda-type

[no] shutdown

Deleting a Card

In order to delete the card type provisioned for a specific slot, you must shutdown existing port
configurations and shutdown and remove all MDA configurations.

Use the following CLI syntax to delete a card provisioned for a specific slot:

CLI Syntax:

config> port

port-id

shutdown

CLI Syntax:

config> card

slot-number

card-type

card-type

mda

mda-number

no mda-type

mda-type

no shutdown

Deleting Port Parameters

Use the following CLI syntax to delete a port provisioned for a specific card/MDA:

CLI Syntax:

config>port

port-id

shutdown

no port

port-id

«
...
155
156
157
158
159
...
»

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 7750 SR OS

Brand: PaloAlto Networks Pages: 3

Brand: QNAP Pages: 39

RUGGEDSWITCH RS900G

Brand: RuggedCom Pages: 23

Brand: FS Pages: 19

Brand: EnGenius Pages: 3

Fieldpoint cFP-RTD-124

Brand: National Instruments Pages: 15

MasterBus Tanklevel Interface

Brand: Mastervolt Pages: 8

Brand: Netis Pages: 16

Compact NVR-AS 4000

Brand: IndigoVision Pages: 38

Brand: Billion Pages: 120

NVRx-7300 series

Brand: Swann Pages: 9

Brand: Talent Pages: 18

Brand: Idis Pages: 18

Brand: Watchguard Pages: 21

Brand: N-Tron Pages: 2

Brand: Brickcom Pages: 184

Brand: New Media Technology Pages: 26

Brand: D-Link Pages: 191

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands