Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 431

Page: 431 / 444

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 431

port

Syntax

port

port-id

statistics

port

port-id

atm

pvc

[

vpi[/vci

]]

statistics

port

port-id

atm

pvp

[

vpi

]

statistics

port

port-id

atm

pvt

[

vpi1.vpi2

]

statistics

port

port-id

atm

ilmi

statistics

port

port-id

atm

port-connection

statistics

Context

clear

Description

This command clears port statistics for the specified port(s).

Parameters

port-id —

The port identifier.

Values

port-id

slot[/mda[/port]] or slot/mda/port[.channel]

aps-id

aps-group-id[.channel]
aps keyword
group-id

1 — 64

bundle-type-slot/mda.bundle-num

bundle

keyword

type

ima, ppp

bundle-num

1 — 128

statistics —

Specifies that port statistics will be cleared.

atm —

Specifies that ATM port statistics will be cleared.

ilmi —

Clears ILMI information. This parameter is only applicable for ports/bundles that support

ILMI.

vpi —

Specifies the ATM network virtual path identifier (VPI) for this PVC.

vci —

Specifies the ATM network virtual channel identifier (VCI) for this PVC.

slot —

The slot number.

Values

1 - 10

mda —

The MDA number.

Default

All MDAs.

Values

1, 2

pvc —

Clears PVC statistics.

port-connection —

Clears port-connection statistics.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 431 / 444

Search results

Summary of Contents for 7750 SR OS

Reviews: