Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 416

Page: 416 / 444

Show Commands

Page 416

7750 SR OS Interface Configuration Guide

A:ima2#

pvt

Syntax

pvt

[

vpi.vpi

] [

detail

]

Context

show>multilink-bundle>ima>atm

Description

This command displays ATM port PVT information.

Parameters

vpi —

Displays the VPI values.

Values

vpi:

0 — 4095 (NNI)
0 — 255 (UNI)

detail —

Provides detailed information.

MDA Values

1, 2

Output

Show Mutlilink-bundle IMA ATM PVT Output —

The following table describes show

multilink-bundle IMA ATM port-connection output fields.

Sample Output

A:ima2# show multilink-bundle bundle-ima-1/1.1 ima atm pvt

================================================================

ATM PVTs, Port bundle-ima-1/1.1

================================================================

VPI Range Owner Type Ing.TD Egr.TD Adm Opr

Label

Description

VPI Range

Displays the VPI range:

Owner

Identifies the system entity that owns a specific ATM connection.

Type

Specifies the type of this multilink bundle.

mlppp —

Indicates that the bundle is of type MLPPP.

ima —

Indicates that the bundle is of type IMA group.

Ing.Td

Specifies the ATM traffic descriptor profile that applies to the receive
direction of the interface connection.

Egr.Td

Specifies the ATM traffic descriptor profile that applies to the transmit
direction of the interface connection.

Adm

ima —

Indicates that the bundle is of type IMA group.

Down —

The bundle is administratively down.

Opr

Up —

The bundle is operationally up.

Down —

The bundle is operationally down.

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Search results

Summary of Contents for 7750 SR OS

Reviews:

Related manuals for 7750 SR OS

Brands by name

Popular brands