manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual, Page: 355 / 444

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 355

Interface Configuration

7750 SR OS Interface Configuration Guide

Page 355

Sample Output

A:ALA-251# show port 1/2/1 detail

===============================================================================

Ethernet Interface

===============================================================================

Description        : 10/100 Ethernet TX

Interface          : 1/2/1                      Oper Speed       : 0 mbps

Link-level         : Ethernet                   Config Speed     : 100 mbps

Admin State        : up                         Oper Duplex      : N/A

Oper State         : down                       Config Duplex    : full

Physical Link      : No                         MTU              : 1514

IfIndex            : 37781504                   Hold time up     : 0 seconds

Last State Change  : 01/03/2008 15:17:00        Hold time down   : 0 seconds

Last Cleared Time  : 01/03/2008 15:17:01

Last Cleared Time  : 01/03/2008 15:17:01

Configured Mode    : network                    Encap Type       : null

Dot1Q Ethertype    : 0x8100                     QinQ Ethertype   : 0x8100

PBB Ethertype      : 0x88e7

Ing. Pool % Rate   : 100                        Egr. Pool % Rate : 100

Net. Egr. Queue Pol: default

Egr. Sched. Pol    : n/a

Auto-negotiate     : false                      MDI/MDX          : unknown

Accounting Policy  : None                       Collect-stats    : Disabled

Egress Rate        : Default                    Ingress Rate     : Default

Load-balance-algo  : default                    LACP Tunnel      : Disabled

Down-when-looped   : Disabled                   Keep-alive       : 10

Loop Detected      : False                      Retry            : 120

Configured Address : 14:30:01:02:00:01

Hardware Address   : 14:30:01:02:00:01

Cfg Alarm          :

Alarm Status       :

===============================================================================

Traffic Statistics

===============================================================================

                                                   Input                 Output

-------------------------------------------------------------------------------

Octets                                                 0                      0

Packets                                                0                      0

Errors                                                 0                      0

===============================================================================

Ethernet Statistics

===============================================================================

Broadcast Pckts  :                   0  Drop Events      :                   0

Multicast Pckts  :                   0  CRC/Align Errors :                   0

Undersize Pckts  :                   0  Fragments        :                   0

Oversize Pckts   :                   0  Jabbers          :                   0

Collisions       :                   0

Octets                         :                   0

Packets                        :                   0

Packets of 64 Octets           :                   0

Packets of 65 to 127 Octets    :                   0

Packets of 128 to 255 Octets   :                   0

Packets of 256 to 511 Octets   :                   0

Packets of 512 to 1023 Octets  :                   0

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments