manualshive.com logo in svg

Alcatel-Lucent 7750 SR OS, Interface Configuration Manual

Share
Download
Alcatel-Lucent 7750 SR OS Interface Configuration Manual Download Page 436

Debug Commands

Page 436

7750 SR OS Interface Configuration Guide

lag

Syntax

lag

 [

lag-id

 

lag-id

 [

port

 

port-id

]] [

all

]

lag 

[

lag-id 

lag-id

 [

port

 

port-id

]] [

sm

] [

pkt

] [

cfg

] [

red

] [

iom-upd

] [

port-state

] [

timers

] [

sel-

logic

] [

mc

] [

mc-pkt

]

no lag 

[

lag-id

 

lag-id

]

Context

debug

Description

This command enables debugging for LAG.

Parameters

lag-id — 

Specifies the link aggregation group ID.

port-id — 

Specifies the physical port ID.

Syntax

: 

slot/mda/port

[.

channel

]

sm — 

Specifies to display trace LACP state machine.

pkt — 

Specifies to display trace LACP packets.

cfg — 

Specifies to display trace LAG configuration.

red — 

Specifies to display trace LAG high availability.

iom-upd — 

Specifies to display trace LAG IOM updates.

port-state — 

Specifies to display trace LAG port state transitions.

timers — 

Specifies to display trace LAG timers.

sel-logic — 

Specifies to display trace LACP selection logic.

mc — 

Specifies to display multi-chassis parameters.

mc-packet — 

Specifies to display the MC-LAG control packets with valid authentication were 

received on this system.

ppp

Syntax

[

no

]

 ppp 

port-id

Context

debug

Description

This command enables/disables and configures debugging for PPP.

Parameters

port-id — 

Specifies the physical port ID

Syntax:

 

port-id

slot/mda/port[.channel]

aps-id

aps-

group-id

[.

channel

]

aps

keyword

group-id 1 — 64

bundle IDbundle-

type

-

slot/mda

.

bundle-num

bpgrp-

type

-

bpgrp-num

bundle keyword

Summary of Contents for 7750 SR OS





























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands