216
Signal and parameter list
3ADW000379R0501 DCS550 Manual e e
Signal / Parameter name
m
in.
ma
x.
def
.
uni
t
30.10 - 30.11 Unused
30.12 M1FldMinTrip (minimum field trip)
The drive trips with F541 M1FexLowCur [FaultWord3 (9.03) bit 8] if M1FldMinTrip (30.12) - in percent of
M1NomFldCur (99.11) - is still undershot when FldMinTripDly (45.18) is elapsed.
Note:
M1FldMinTrip (30.12) is not valid during field heating. In this case, the trip level is automatically set to 50 % of
M1FldHeatRef (44.04). The drive trips with F541 M1FexLowCur [FaultWord3 (9.03) bit 8] if 50 % of
M1FldHeatRef (44.04) is still undershot when FldMinTripDly (45.18) is elapsed.
Int. Scaling: 100 == 1 % Type: I
Volatile:
N
0
100
50
%
30.13 M1FldOvrCurLev (field overcurrent level)
The drive trips with F515 M1FexOverCur [FaultWord1 (9.01) bit 14] if M1FldOvrCurLev (30.13) - in percent of
M1NomFldCur (99.11) - is exceeded. It is recommended to set M1FldOvrCurtLev (30.13) at least 25 % higher
than M1NomFldCur (99.11).
The field overcurrent fault is inactive, if M1FldOvrCurLev (30.13) is set to 135 %.
Int. Scaling: 100 == 1 % Type: I
Volatile:
N
0
135
125
%
30.14 SpeedFbMonLev (speed feedback monitor level)
The drive reacts according to SpeedFbFltSel (30.17) or trips with F553 TachPolarity [FaultWord4 (9.04) bit 4]
if the measured speed feedback [SpeedActEnc (1.03) or SpeedActTach (1.05)] does not exceed
SpeedFbMonLev (30.14) while the measured EMF exceeds EMF FbMonLev (30.15).
Internally limited from:
rpm
to
rpm
20000
32767
*
)
29
.
2
(
0
Example:
With SpeedFbMonLev (30.14) = 15 rpm and EMF FbMonLev (30.15) = 50 V the drive trips when the EMF is >
50 V while the speed feedback is
≤
15 rpm.
Int. Scaling: (2.29) Type: I
Volatile:
N
0
10000
15
rp
m
30.15 EMF FbMonLev (EMF feedback monitor level)
The speed measurement monitoring function is activated, when the measured EMF exceeds EMF FbMonLev
(30.15). See also SpeedFbMonLev (30.14).
Int. Scaling: 1 == 1 V
Type: I
Volatile:
N
0
2000
50
V
30.16 M1OvrSpeed (overspeed)
The drive trips with F532 MotOverSpeed [FaultWord2 (9.02) bit 15] if M1OvrSpeed (30.16) is exceeded. It is
recommended to set M1OvrSpeed (30.16) at least 20 % higher than the maximum motor speed.
Internally limited from:
rpm
to
rpm
20000
32767
*
)
29
.
2
(
0
The overspeed fault is inactive, if M1OvrSpeed (30.16) is set to zero.
Int. Scaling: (2.29)
Type: I
Volatile:
N
0
10000
1800
rp
m
Summary of Contents for DCS550 Series
